超高分子量聚乙烯板材板的性能及属性（Properties and properties of ultra high molecular weight polyethylene sheet）.docVIP

下载本文档

3
0
约8.44千字
约 10页
2017-08-04 发布于河南
举报
版权申诉

超高分子量聚乙烯板材板的性能及属性（Properties and properties of ultra high molecular weight polyethylene sheet）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

超高分子量聚乙烯板材板的性能及属性（Properties and properties of ultra high molecular weight polyethylene sheet） 1, mechanical properties Index name index unit test method The density of g/cm3 ASTM1505 0.94 The fracture strength of MPa D638 42 Elongation% D638 350 Charpy notched impact strength of Kj/m2 D256 = 100 2. thermal properties: Index name index measurement unit The melting point of 136 DEG ASTMD2117 VEKA softening point 134 C ASTMD1512 The thermal expansion coefficient of 10-4/ 1.5 C ASTMD648 Heat deformation temperature of 90 C ASTMD648 (4.6kg/cm2) Electrical properties: Index name index unit test method The volume resistivity of ASTMD257 1017 ohm cm. The surface resistance coefficient ASTMD257 1013 ohm The dielectric strength of kV / mm ASTMD149 900 The dielectric coefficient of the 106 Hz ASTMD150 2.3 Cold tolerance The molecular weight of more than 500 thousand high density polyethylene, brittle temperature to -140 deg. C. Ultra high molecular weight polyethylene can even in liquid nitrogen or helium under the influence, the use of temperature can reach below -269 DEG C, there is still a certain mechanical strength. Wear resistance The wear resistance of UHMWPE is excellent, the higher the molecular weight, the better wear resistance of the material. High contrast with other material wear parameters UHME-PE PTFE PA66 45# POM material stainless steel yellow steel The wear rate average of 0.74 2.31 1.51 3.1 4.02 4.05 16.74 Note: wear test performance: Sand / water =3/2 (important) with 16 ~24 mesh / between construction sand specimens, 800 rpm, test piece as 60mm * 40MM * 3mm, each specimen was worn for 7 hours. Ultra high molecular weight polyethylene wear rate The name of the product molecular weight average wear rate Ultra high molecular weight polyethylene 5 million 700 thousand 0.30 4 million 0.41 3 million 800 thousand 0.45 2 million 800 thousand 0.50 1 million 600 thousand 0.74 6. impact strength UHMWPE HDPE ABS PA66 PC POM material PTEE impact strength Kj/m2 = 1002