降低光纤接头熔接损耗的方法（Method for reducing splice loss of optical fiber connector）.docVIP

下载本文档

3
0
约1.94万字
约 17页
2017-08-17 发布于河南
举报
版权申诉

降低光纤接头熔接损耗的方法（Method for reducing splice loss of optical fiber connector）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

降低光纤接头熔接损耗的方法（Method for reducing splice loss of optical fiber connector）

降低光纤接头熔接损耗的方法（Method for reducing splice loss of optical fiber connector） Method for reducing splice loss of optical fiber joint 1 the concept of splice loss in optical fiber joints Optical fiber welding is a fully automatic special equipment - Splitter (Fusion), which will be used in two fiber optic cables The fibers that need to be connected are joined together and welded together by using a short arc to fuse the ends of the two optical fibers As a whole, the connection method has the advantages of small size, high mechanical strength and stable performance after the splicing of the optical fiber, so the utility model has wide application. When the fiber is connected, light transmission to the joint will produce a certain amount of loss, called fusion loss or splice loss. Because The quality of optical fiber splicing affects the transmission loss of optical fiber lines, and the parameters of optical fiber transmission lines, such as no relay amplification and transmission distance, etc., Therefore, the splice loss at the optical fiber joint is required to be as small as possible to ensure the transmission quality of the fiber CATV signal. At present, most welding methods can make welded joints less than 0.1dB, or even less than 0.05 DB level, for specific optical fiber CATV engineering, can be based on specific circumstances, such as optical fiber line, relay section length, light The power of the equipment, the sensitivity of reception and the number of the system, etc., determine the allowable value of the splice loss at each fiber joint As a welding loss index, it is clearly stipulated in the relevant technical documents. Each relay on an optical CATV transmission line The transmission loss of the transmission line should also be clearly defined, because the optical fiber joint is measured after all the welding is finished The quality index is the transmission loss of the optical fiber line. Now the target is below 0.25dB/km (including welding loss) Consume). B