精基准的选择原则（The selection principle of the benchmark fine）.docVIP

下载本文档

9
0
约6.3千字
约 5页
2017-08-17 发布于河南
举报
版权申诉

精基准的选择原则（The selection principle of the benchmark fine）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

精基准的选择原则（The selection principle of the benchmark fine）

精基准的选择原则（The selection principle of the benchmark fine） Selection principle of precise benchmark Where are you now?: Selection principle of precise benchmark In the process planning, the selection of the positioning benchmark is correct or not, and the accuracy and position of the parts can be guaranteed Precision requirements, and the parts of each surface processing sequence arrangement have great influence, when the fixture installation workpiece, positioning The choice of benchmark also affects the complexity of the fixture structure. Therefore, the selection of location reference is a very important process problem. When choosing the positioning datum, it is necessary to guarantee the machining accuracy of the workpiece. Therefore, the selection of the positioning benchmark should first select the precise datum, and then select the rough datum. Selection of fine base on time, the main consideration should be given to ensure the machining accuracy and workpiece installation convenient and reliable. The selection principle is as follows: (1) principle of coincidence of datum That is, the design benchmark is used as the positioning reference to avoid the misalignment error caused by the misalignment between the reference datum and the design datum. The parts shown in Figure 4-22 are designed sizes a and C, and the top surface B and the bottom A have been machined (i.e. size a has been guaranteed), and now the C surface of a batch of parts is adjusted by adjusting method. To ensure that the design dimension C is positioned on the A surface, the positioning reference A does not coincide with the design reference B, as shown in Figure B. Since the milling cutter is adjusted relative to the fixture positioning surface (or machine tool table), the position of the tool is no longer changed after adjustment of the tool. After processing the size of C in addition to the size of processing error (J) effect, and the error on the procedures of the relevant (Ta). This error i