h3cvlan配置.docxVIP

一：配置基于端口的VLAN创建vlan2并进入视图H3C system-view[H3C] vlan 2# 指定VLAN2 的描述字符串为home。[H3C-vlan2] description home# 向VLAN2 中加入端口Ethernet1/0/1 和Ethernet1/0/2。[H3C-vlan2] port Ethernet 1/0/1 Ethernet 1/0/2# 创建VLAN3 并进入其视图。[H3C-vlan2] vlan 3# 向VLAN3 中加入端口Ethernet1/0/3 和Ethernet1/0/4。[H3C-vlan3] port Ethernet 1/0/3 Ethernet 1/0/4二：IP 地址配置举例# 配置VLAN 接口2 的IP 地址。H3C system-view[H3C] interface Vlan-interface 2[H3C-Vlan-interface2] ip address 129.2.2.1 255.255.255.0# 配置VLAN 接口3 的IP 地址。H3C system-view[H3C] interface Vlan-interface 3[H3C-Vlan-interface3] ip address 192.2.2.1 255.255.255.0配置好后，交换机上ping各网关之间应该能够互通，在配置好的端口上连上pc设置好ip如pc1接Ethernet1/0/1 设置ip：129.2.2.2 255.255.255.0 129.2.2.1Pc2接Ethernet 1/0/3 设置ip：192.2.2.2 255.255.255.0 192.2.2.1则pc1和pc2能互通S3600三层交换机端口限速配置：[H3C]interface Ethernet1/0/4[H3C-Ethernet1/0/4]line-rate outbound 1024 ---该端口的出方向报文流量限速1M[H3C-Ethernet1/0/4]broadcast-suppression pps 1024 ---该端口接收广播流量限速1M[H3C-Ethernet1/0/4]multicast-suppression pps 1024 ---该端口接收组播流量限速1M[H3C-Ethernet1/0/4]unicast-suppression pps 1024 ---该端口接收未知单播流量限速1M[H3C-Ethernet1/0/4]flow-control ---开启以太网端口的流量限制功能（缺省情况下是关闭状态的）建立并配置VLANsystem-view//进入配置模式[H3C]vlan 10//建立VLAN 10[H3C-vlan10]port Ethernet1/0/19 //把Ethernet1/0/19 加入到VLAN 10里面[H3C-vlan10]name test//名字为test[H3C-vlan10]descriptio test//描述为test[H3C-vlan10]quit//退出vlan 10[H3C]interface vlan 10进入VLAN 300里[H3C-Vlan-interface10]ip address 192.168.1.1 255.255.255.0配置IP地址VLAN 20的配置[H3C]vlan 20//建立vlan 20[H3C-vlan20]port Ethernet 1/0/10 to Ethernet 1/0/15//把端口1/0/10到1/0/15加入到vlan 20里[H3C-vlan20]name jishu[H3C-vlan20]descriptiojishu[H3C-vlan20]quit[H3C]interface vlan 20[H3C-Vlan-interface20]ip address 192.168.2.1 255.255.255.0[H3C-vlan10]undo port Ethernet1/0/19//VLAN里面端口的删除[H3C]undo vlan 10//VLAN的删除ip route-static 0.0.0.0 0.0.0.0 192.168.0.1 preference 60//建立默认路由建立DHCP中继[H3C]dhcp-server 1 ip 192.168.8.9//配置dhcp服务器IP[H3C]dhcp relay information enable//启动DHCP中继服务[H3C]interface vlan 10//进入VLAN 10接口[H3C-Vlan-interface10]dhcp-server 1//设置vlan 10接口的DHCP-serve