制造技术基础试题附答案（Manufacturing technology basic questions with answers）.docVIP

下载本文档

27
0
约 12页
2017-08-20 发布于河南
举报
版权申诉

制造技术基础试题附答案（Manufacturing technology basic questions with answers）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

制造技术基础试题附答案（Manufacturing technology basic questions with answers）

制造技术基础试题附答案（Manufacturing technology basic questions with answers） I. judgment questions 15 points 1. in cutting, there is only one feed motion. (V) 2. the main angle between the main cutting edge and the feeding direction is C. (X) 3. cutting temperature is the main factor affecting tool durability. (X) 4. the rake angle increases and the cutting deformation increases. (V) The 5. process is the basic unit of the process. (V) 6. incomplete positioning is not allowed in the location scheme of the parts. (V) 7. the rough base can be used again and again in the same dimension. (X) 8. using six supporting nails to locate the workpiece limits the six degrees of freedom of the workpiece. (V) 9. boring hole, boring cutter tip installation is low, good anti vibration. (X) 10. the residual compressive stress produced on the machined surface layer can improve the fatigue strength of the parts. (V) Two. Choose 15 One of the functions of the 1. cutting edge angle is to control the chip flow. If the rake angle is negative, the chip flow is (A). A flowing to the machined surface, B. flows to the machined surface, and C flows out of the normal direction of the cutting edge 2. rough machining, the front angle should take () the value; when finishing, the front angle should be taken (A) value; the greater the plasticity of the processed material, The front angle should take () the value; when the brittle material is processed, the front angle should be taken (or); the higher the strength and the hardness of the material, the higher the front angle should be. A is relatively large, B. is relatively small, C. takes arbitrarily 3., the influence of cutting parameters on the cutting temperature is from big to small, and the arrangement is (B). A.vc, AP, F, B.vc, F, C.f, AP, VC, D.ap, AP, F, VC 4. prepare the machining process specification of parts, prepare production plan and carry out cost accounting, the basic unit is (D). A. step, B. process, C. station, D. installation The standard