V带传动设计C语言.docVIP

#includeiostream.h #include math.h #include stdio.h #includeiomanip #includefstream using namespace std; #define pi 3.1415926 int x,y,i,j,a,z,e,t;//z为v带的条数m,n, double c1,c2,a0,a1,lc,lj,l,b,amin,amax; int n1,n2;//n1为小带轮的速度，n2为大带轮的速度 int lh;//lh为电动机工作时间 double k,v,u,ka,al,kl;//k为工作情况系数,v为V带的速度,u为传动比,ka为包角系数,al为包角 double p,pc,p1,p0;//p为电动机的功率,pc为计算功率,p1为单根普通V带所能传递的功率，p0为单根普通V带传动功率的增量 double d1,d2;//d1,d2分别为大小带轮的直径 int g;//g表示工作机的工作状况：g=1,2,3,4分别表示稳，变动小，变动大，变动很大 double cc[5];//数组cc里的各元素依次表示Z,A,B,C,D,E型电动机边界线的C值 double f0,q;//f0为V带的张紧力，q为V带作用在轴上的压轴力 int s;//s=1表示为第一类原动机，s=2表示为第二类原动机 static double aa[6][17]= {{0,0.00039,0.06,0.246,7.44,4.41e-5,0.72,0.00043,9.8e-08,435,50,63,71,80,90,1,13}, {0,0.00103,0.1,0.449,19.62,7.65e-5,0.68,0.000225,2.25e-08,100,75,90,100,112,125,5,18}, {0,0.00265,0.17,0.794,50.6,1.31e-4,0.68,0.000174,1.94e-08,27,125,140,150,170,180,8,24}, {0,0.0075,0.3,1.48,143.2,2.43e-4,0.70,0.00964,4.48e-7,7.2,200,224,236,265,280,14,29}, {0,0.0266,0.62,3.15,507.3,4.77e-4,0.78,3.38e-5,0,0.92,355,400,425,475,500,18,32}, {0,0.0498,0.9,4.57,951.5,7.06e-4,0.706,4.95e-5,1.254e-9,0,500,560,630,800,900,22,33}}; static char bb[6]={Z,A,B,C,D,E}; static int ll[34]={0,400,450,500,560,630,710,800,900,1000,1120,1250,1400, 1600,1800,2000,2240,2500,2800,3150,3550,4000,4500,5000, 5600,6300,7100,8000,9000,10000,11200,12500,14000,16000}; //*********P1,P2为功率增量矩阵******** double P1[6][11]= {{0.01,0.01,0.01,0.02,0.02,0.02,0.02,0.03,0.03,0.04,0.04}, {0.01,0.02,0.02,0.02,0.03,0.03,0.03,0.04,0.04,0.04,0.05}, {0.04,0.07,0.08,0.08,0.11,0.13,0.15,0.19,0.23,0.26,0.30}, {0.05,0.09,0.10,0.11,0.15,0.17,0.19,0.24,0.29,0.34,0.39}, {0.10,0.17,0.20,0.23,0.30,0.36,0.39,0.49,0.59,0.69,0.79}, {0.13,0.22,0.25,0.30,0.38,0.46,0.51,0.63,0.76,0.89,1.01}}; double P2[6][11]={{0.14,0.21,0.27,0.34,0.41,0.48,0.55,0.65,0.82,0.99,1.10}, {0.18,0.26,0.35,0.44,0.53,0.62,0.71,0.83,1.06,1.27,1.41}, {0.49,0.73,0.97,1.22,1.46,1.70,1.95,2.31,2.92,3.52,3.89}, {0.63,0.94,1.25,1.56,1.88