摄像机安装高度步骤（The camera installation height step）.docVIP

下载本文档

3
0
约5.82千字
约 5页
2017-08-21 发布于河南
举报
版权申诉

摄像机安装高度步骤（The camera installation height step）.doc

1、本文档共5页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

摄像机安装高度步骤（The camera installation height step）

摄像机安装高度步骤（The camera installation height step） If the camera is fixed monitoring a position without turning, so only the camera bracket can meet the requirements. Ordinary camera bracket has the advantages of simple installation, low price and variety. The stent has short, long, straight, curved, choose different models according to different requirements. The outdoor bracket is in line with the requirements of the main load capacity, there is the installation position, because in practice we found that many outdoor camera installation position, some mounted on a pole, and some in the tower, or installed in the rack...... Due to various reasons, the existing support may be difficult to meet the requirements, require additional processing or improvement, there is not more to say. Indoor camera installation height to 2.5 ~ 5m is appropriate, outdoor in 3.5 ~ 10m is appropriate; elevator installation at the top corner and into elevator operator, and the two wall of the camera optical axis with the lift and ceiling to 45 degrees. The camera installation notes The camera is easy to use, as long as the correct installation of lens, communication signal cable, power can work. But in actual use, if not properly install and adjust the camera lens and the lens of the state, it may not reach the expected effect. Should pay attention to the camera lens and the interface is C interface or CS interface (which is a point to remember, or by C directly to the CS interface on the camera lens is screwed into the most likely damaged CCD chip camera). Install the camera, remove the camera lens and the first protective cover, and then gently screwed into the camera lens interface and make the place. The auto iris lens, should also be connected to the control line lens automatic aperture camera interface, for two or three variable electric variable lens lens, as long as the rotation of the lens in place temporarily without correcting the balance (only after the focus after the adjustment