dd 命令用来测试硬盘读写速度（The DD command is used to test the hard disk read and write speed）.docVIP

下载本文档

9
0
约5.8千字
约 9页
2017-08-21 发布于河南
举报
版权申诉

dd 命令用来测试硬盘读写速度（The DD command is used to test the hard disk read and write speed）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

dd 命令用来测试硬盘读写速度（The DD command is used to test the hard disk read and write speed）

dd 命令用来测试硬盘读写速度（The DD command is used to test the hard disk read and write speed） The DD command is used to test the hard disk read and write speed Classification: Original address: DD command is used to test the hard disk read and write speed (RPM) author: w200916-gmail The DD command is used to test the hard disk read and write speed (RPM) DD is a very useful command under Linux/UNIX, is a copy of a file with the specified size of the block, and the specified conversion in the copy at the same time. The 1. main options DD command: If the specified number of characters at the end of the following places multiplied by the corresponding number: B=512, c=1, k=1024, w=2, xm=number, M If=file Enter the file name, the default is the standard input. Of=file The output file name, the default is the standard output. Ibs=bytes One reads bytes bytes (i.e. a block size is bytes bytes). Obs=bytes Write a bytes bytes (i.e. a block size is bytes bytes). Bs=bytes At the same time set to read and write the block size is bytes, it can replace IBS and obs. Cbs=bytes A conversion to bytes bytes, i.e. conversion buffer size. Skip=blocks Copy from the input file at the beginning of a block and then start to skip blocks. Seek=blocks Copy the output files from the beginning and then start to skip the blocks block. (usually only when the output file is valid only when the disk or tape). Count=blocks Just copy the blocks block, IBS block size is equal to the specified number of bytes. Conv=conversion[, conversion...] Convert the file with the specified parameters. Conversion parameters: ASCII convert EBCDIC to ASCII. EBCDIC convert ASCII to EBCDIC. IBM ASCII for alternate EBCDIC. conversion Block put each line into the length of the CBS record, the insufficient part is filled in with spaces. Unblock makes every line length is CBS, the insufficient part is filled in with spaces. Lcase the uppercase characters converted to lowercase characters. Ucase the lowercase characters converted to upp