大一机械制图经典复的习包含试卷及答案.ppt

复习要点;答疑时间、地点：关注教务处网站通知;点、线、面、体;第十章 图样画法;第十章 图样画法;第十章 图样画法;;本学期内容;一、内、外螺纹及其连接的画法（P244图11-8） ;A;A－A;;Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.;二、常用键的种类、型式、标记和连接画法：;注意： 键 联 接 的 画 法;键 b×d1 GB/T 1099;键 b×L GB/T 1565;钩头楔键联结的画法;;b;圆柱销GB/T 119.1-2000;零件1;;五、螺纹紧固件连接的画法 ; 1、螺栓连接的比例画法（P253图11-16、图11-17）;;常见螺钉连接图（P256图11-24） ;3. 双头螺柱连接及其画法 ; 紧定螺钉常用于定位、防松而且受力较小的情况 。 ;轴承;六、两圆柱齿轮啮合的画图要点（P266图11-45） ：;齿轮啮合的画法;齿轮啮合区放大图; 在平行于齿轮轴线的投影面上的外形视图中，啮合区只用粗实线画出节线，齿顶线和齿根线均不画。在两齿轮其它处的节线仍用细点画线绘制(图a)。如需表示轮齿的方向时，画法与单个齿轮相同(图b和c)。 ; 在装配图中，被弹簧遮挡的结构一般不画出，可见部分应从弹簧的外轮廓线或从弹簧钢丝剖面的中心线画起 ;在装配图中弹簧的画法;主视图投射方向;;主视图投射方向;;主视图投射方向;;主视图投射方向;立体图;表达一 ;读者可自行分析，并比较其优缺点。 ;;一、标准件、常用件;Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.;一、标准件、常用件;Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.;Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.;Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.;Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.;将图中所缺的部分画完整。;Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.;二、零件图;Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.;Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.;Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.;;;Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd.;三、装配图;Evaluation only. Created with Aspose.Slides for .NET 3.5 Clien