【内存条维修技巧之三】 典型故障检测分析和维修实例([memory repair skills] three typical fault detection and analysis and maintenance examples).docVIP

【内存条维修技巧之三】 典型故障检测分析和维修实例([memory repair skills] three typical fault detection and analysis and maintenance examples).doc

  1. 1、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。。
  2. 2、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载
  3. 3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
  4. 4、该文档为VIP文档,如果想要下载,成为VIP会员后,下载免费。
  5. 5、成为VIP后,下载本文档将扣除1次下载权益。下载后,不支持退款、换文档。如有疑问请联系我们
  6. 6、成为VIP后,您将拥有八大权益,权益包括:VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
  7. 7、VIP文档为合作方或网友上传,每下载1次, 网站将根据用户上传文档的质量评分、类型等,对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档
查看更多
【内存条维修技巧之三】 典型故障检测分析和维修实例([memory repair skills] three typical fault detection and analysis and maintenance examples)

【内存条维修技巧之三】 典型故障检测分析和维修实例([memory repair skills] three typical fault detection and analysis and maintenance examples) This article is contributed by jgzxljf [three] memory maintenance and maintenance examples of typical fault detection and analysis of memory maintenance techniques three] published in the 2008-8-23 08:04 | only see the author | reverse the kantie | print on 2009-8-27 22:41 / E babe editor Y8 I ); S) {) process fault and particle pin welding this is one of the most common non device type. Phenomenon: when directly inserted into the motherboard alarm, the motherboard is not lit. With a good band, you can boot the system under DOS. Detection: RST test, one or several bits of data, the depth of the column capacity, very neatly displayed red. Measure relative data with multimeter. 22 ohm current limiting resistor has no resistance change. Reason: because of the process, when the factory produces the memory, the reflow soldering is not completely welded in place, only the pin of the particle is slightly adhered to the soldering tin. The memory in the process of long-term use, high temperature can make the solder pins gradually fusing, oxidation, and the connection of circuit breaker. Troubleshooting: DDR1 particles: in the fault pin dip a little particle flux, with the method of drag soldering, welding pin once and for all. DDR2 particles: particle flux after the subsidy with a hot-air gun blowing around, if ineffective, remove particles after replanting and tin particles. Attention: when the welding is finished, insert the main board and make sure the cleaning of the finger is done. Attached: maintenance equipment: Hodge 865GV motherboard with AGP graphics, RST detection software, other tools. Similar phenomenon: 1, when the stop resistance occurs, this phenomenon will occur, but the solution is not the same, the latter will introduce. 2, the physical location of the data pin of the particle is damaged, but the solution is different. 3, gold finger dirt w

您可能关注的文档

文档评论(0)

f8r9t5c + 关注
实名认证
文档贡献者

该用户很懒,什么也没介绍

版权声明书
用户编号:8000054077000003

1亿VIP精品文档

相关文档