奥迪a6轿车传感器标准值（Standard value of sensor for Audi A6 car）.docVIP

下载本文档

4
0
约1.7万字
约 25页
2017-08-31 发布于河南
举报
版权申诉

奥迪a6轿车传感器标准值（Standard value of sensor for Audi A6 car）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

奥迪a6轿车传感器标准值（Standard value of sensor for Audi A6 car）

奥迪a6轿车传感器标准值（Standard value of sensor for Audi A6 car） Standard value of sensor for Audi A6 car Audi A6 sedan First, ANQ engine electronic control system sensor standard value 1. Holzer sensor Test condition Standard value Connect the Holzer sensor connector terminals 1 and 2 with the diode test light and start the engine The diode test lamp flashes 1 times for each turn of the crankshaft 2 turns Connect the digital multimeter to the sensor connector terminals 1 and ground and screw the ignition switch to the ON position to measure the voltage 4.5 ~ 5.5V [img, 252226]file:///C:/DOCUME~1/ADMINI~1/LOCALS~1/Temp/ksohtml/wps_clip_image1.jpg[/img] 2. engine speed sensor Test condition Standard value Disconnect the engine speed sensor and measure the resistance between the engine speed sensor joint terminals 1 and 3 using a digital multimeter 450~1000 Omega [img, 316187]file:///C:/DOCUME~1/ADMINI~1/LOCALS~1/Temp/ksohtml/wps_clip_image2.jpg[/img] 3. inlet temperature sensor Test condition Standard value Measure the resistance between the inlet temperature sensors connector terminals 1 and 2 At 30 degrees centigrade, the resistance is 1500~2000 ohms At 80 degrees centigrade, the resistance is 275~375 ohms [img, 275209]file:///C:/DOCUME~1/ADMINI~1/LOCALS~1/Temp/ksohtml/wps_clip_image3.jpg[/img] 4. oxygen sensor Test condition Standard value Start the engine at idle speed and use a digital multimeter to measure the voltage between the oxygen sensor terminals 1 and 2 11 ~ 15V Start the engine at idle speed and use a digital multimeter to measure the voltage between the oxygen sensor terminals 3 and 4 0.4 ~ 0.5V [img, 300308]file:///C:/DOCUME~1/ADMINI~1/LOCALS~1/Temp/ksohtml/wps_clip_image4.jpg[/img] 5. air flow sensor Test condition Standard value Pull off the air flow sensor connector, screw the ignition switch to the ON position, and measure the voltage between the air flow sensor connector terminal 2 and the ground of the engine with a digital multimeter Battery voltage Pul