雕刻机保养及故障排除（Engraving machine maintenance and troubleshooting）.docVIP

下载本文档

0
0
约6.45千字
约 5页
2017-09-01 发布于河南
举报
版权申诉

雕刻机保养及故障排除（Engraving machine maintenance and troubleshooting）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

雕刻机保养及故障排除（Engraving machine maintenance and troubleshooting）

雕刻机保养及故障排除（Engraving machine maintenance and troubleshooting） Daily maintenance and maintenance of engraving machines Engraving machine for precision CNC equipment, the necessary day-to-day maintenance and maintenance of the machines life and accuracy is essential. Please maintain and maintain the following requirements. maintain First, the continuous running time of 10 hours per day below, to ensure the cooling water cleaning and water pump normal work, must not cause water spindle motor water shortage phenomenon, regular replacement of cooling water, in order to prevent the water temperature is too high. In winter, if the working environment is too low, the water in the tank can be changed into antifreeze. Two, every time the machine is used, should pay attention to cleaning, be sure to platform and drive system dust cleaning, regular (week) for the transmission system (X, Y, Z three axis) lubrication, refueling. (Note: X, Y, Z three axis rod oil maintenance; wire rod part with high speed in winter; if the ambient temperature is too low, screw rod (square or circular guide rail) part should use gasoline to wash clean, then add oil, otherwise it will cause the machine transmission part resistance as a result of excessive machine dislocation). Three, the maintenance of electrical equipment inspection is, must cut off the power supply, until the monitor does not show and the main loop power indicator lights out, you can proceed. Maintain Engraving machine parameter modification (Weihong system): manufacturers modify parameters (input password: NCSTUDIO, click OK): travel of table (based on the machine type and system parameters): in the default on the basis of the first four are selected. Motor parameters: if the lead is 10, then 0.0062, if the lead is 5, then the 0.003125 take-off frequency: 300 Z axis maximum speed: 1000, single axis acceleration: 400, bend acceleration: 300 Repair When the engraving machine fails to work properly, it may be that there is a problem