Standard Test Method for Wear Preventive （穿防护的标准试验方法）.pdfVIP

下载本文档

7
0
约2.49万字
约 3页
2017-09-02 发布于浙江
举报
版权申诉

Standard Test Method for Wear Preventive （穿防护的标准试验方法）.pdf

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

Standard Test Method for Wear Preventive （穿防护的标准试验方法）

An American National Standard Designation: D 2266 – 01 Standard Test Method for Wear Preventive Characteristics of Lubricating Grease (Four-Ball Method)1 This standard is issued under the ﬁxed designation D 2266; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript epsilon () indicates an editorial change since the last revision or reapproval. This test method has been adopted for use by government agencies to replace Method 6514 of Federal Test Method Standard No. 791b. fourth 1 1. Scope ⁄ 2in. diameter steel ball, referred to as the top ball, is 1.1 This test method covers the determination of the wear pressed with a force of 40 kgf (392 N) into the cavity formed preventive characteristics of greases in sliding steel-on-steel by the three clamped balls for three-point contact. The tem- applications. It is not intended to predict wear characteristics perature of the lubricating grease specimen is regulated at 75°C with metal combinations other than steel-on-steel or to evaluate (167°F) and then the top ball is rotated at 1200 rpm for 60 min. the extreme pressure characteristics of the grease. Lubricants are compared by using the average size of the scar 1.2 The values stated in SI units are to be regarded