- 1、本文档共8页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
电脑无法开机,自我检测方法(Computer can not boot, self-test methods)
电脑无法开机,自我检测方法(Computer can not boot, self-test methods)
BIOS battery discharge (restore BIOS factory default), suggest plug in the graphics card, memory, clean up the health, and Polished graphics cards, memory gold fingers.
No troubleshooting of computer boot.
The first step: first of all, check the computers external wiring is connected, put each line re inserted, to see if the failure is ruled out.
The second step: if the fault persists, check whether the excess metal chassis and then open the main chassis, or deformation caused by short circuit board, the chassis has no smell of burnt paste flavor, the motherboard has no burnt chip capacitor around CPU are damaged.
The third step: if not, then clean the dust on the motherboard, and then check the computer is normal.
The fourth step: if the fault persists, then unplug the Reset line on the motherboard and other switches, light connection, and then short-circuit switch with a screwdriver to see whether it can boot.
The fifth step: if you can not boot, then use the minimum system method, the data line of hard disk, floppy drive, CD-ROM pulled out, and then check whether the computer can boot, if the computer displays the boot screen, the problem in these devices. Then, each of these devices is connected to the computer one by one, when access to a device, the failure to reproduce, indicating that the fault is caused by this device, and finally focus on the inspection of this device.
The sixth step: if the fault remains, the fault may be caused by memory, graphics cards, CPU, motherboards and other devices. Then, the memory, graphics card, CPU and other equipment are checked by using the plug and play method and the switching method. If damaged devices are replaced, the damaged equipment is replaced.
The seventh step: if the memory, graphics card, CPU and other equipment is normal, then the BIOS discharge, the use of isolation, the board will be placed on the outside of the chassis, connected to memory, video card,
您可能关注的文档
- 班前会(Pre class meeting).doc
- 球形云台(Spherical tilt table).doc
- 球墨铸铁的热处理(Heat treatment of nodular cast iron).doc
- 班任经验材料水利(Class, experience, materials, water conservancy).doc
- 珍珠粉使用方法(Pearl powder usage).doc
- 珍珠粉的常用用法(Common usage of pearl powder).doc
- 球磨机小齿轮轴承座振动的原因分析(Vibration analysis of pinion bearing housing of ball mill).doc
- 珠宝攻略(Jewelry introduction).doc
- 球蟒饲养(Ball pythons breeding).doc
- 理化因素(Physical and chemical factors).doc
文档评论(0)