硬度hrc,hv,hb-硬度换算（Hardness HRC, HV, hb- Hardness Conversion）.doc

下载文档 降价啦

183
0
约8.68千字
约 8页
2017-09-02 发布于河南
举报
版权申诉
保障服务

硬度hrc,hv,hb-硬度换算（Hardness HRC, HV, hb- Hardness Conversion）.doc

1、本文档共8页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。

硬度hrc,hv,hb-硬度换算（Hardness HRC, HV, hb- Hardness Conversion）

硬度hrc,hv,hb-硬度换算（Hardness HRC, HV, hb- Hardness Conversion） Hardness HRC, HV, HB- Hardness Conversion Date: 2008-10-06 hardness Hardness Conversion formula: 2. Shaw hardness (HS) = Rockwell hardness (HRC) +15 3. Brinell hardness (BHN) = Rock hardness (HV) 4. (Rockwell hardness (HRC) +3) *10= Brinell hardness (BHN) Range of hardness: HS100 HB500 HRC70 HV1300 (80~88) HRA, (85~95) HRB, (20~70) HRC Rockwell hardness, HRA, HRB, HRC and other A, B, C, for three different standards, known as the scale A, ruler B, ruler C. Rockwell hardness test is one of several ordinary indentation hardness tests used nowadays. The initial pressures of three kinds of scales are 98.07N (10kgf). Finally, the hardness values are calculated according to the indentation depth. Ruler A is using a spherical cone diamond indenter, and then pressurized to 588.4N (60kgf); the ruler B is using 1.588mm diameter (1/16 inches) of the ball as the head, and then pressurized to 980.7N (100kgf); and C and A scale scale using the same as the diamond cone ball head, but after the pressurization of the force is 1471N (150kgf). Therefore, the ruler B applies relatively soft material, while the ruler C applies stiffer materials. It has been proved that the hardness values and the strength values of metal materials have an approximate corresponding relationship between the hardness values and the strength values. Because the hardness is determined by the initial plastic deformation resistance and the continuous plastic deformation resistance, the higher the strength of the material, the higher the plastic deformation resistance and the higher the hardness. But the conversion relationship of various materials is not consistent. Hardness indicates the ability of a material to resist hard material pressing into its surface. It is one of the important properties of metallic materials. Generally, the higher the hardness, the better the wear resistance. Commonly used hardness indicators are Brinell hardness, Rockwell