- 1、本文档共11页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
tress Analysis of Bolted Joints Part I. Numerical ...(一绺头发分析螺栓接合部分即数值u2026)
Modern Mechanical Engineering, 2014, 4, 35-45
Published Online February 20 14 (/journal/mme)
/10.4236/mme.2014.41005
Stress Analysis of Bolted Joints Part I.
Numerical Dimensioning Method
László Molnár, Károly Váradi, Balázs Liktor
Department of Machine and Product Design, Budapest University of Technology and Economics, Budapest, Hungary
Email: varadik@eik.bme.hu
Received November 4, 2013; revised December 21, 2013; accepted January 14, 2014
Copyright © 2014 László Molnár et al. This is an open access article distributed under the Creative Commons Attribution License,
which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited. In accor-
dance of the Creative Commons Attribution License all Copyrights © 2014 are reserved for SCIRP and the owner of the intellectual
property László Molnár et al. All Copyright © 2014 are guarded by law and by SCIRP as a guardian.
ABSTRACT
For up-to-date bolted joints, first of all in vehicles, high strength bolts of 10.9 or even 12.9 are used, which are
pre-tightened up to 90% or even 100% of the yield strength. The primary aim of this high degree utilization is
the weight reduction. For the analytic dimensioning of bolted joints, the VDI 2230 Richtlinien German standard
provides support. However, the analytic model can mostly consider the true structural characteristics only in a
limited way. The analytic modeling is especially uncertain in case of multiple bolted joints when the load distri-
bution among the bolts depends reasonably upon the elastic deformation of the participating elements in the
joints over the geometry of the bolted joint. The first part of this paper deals with the problems of numerical
modeling and stress analysis,
您可能关注的文档
- Training Courses 2010 EDF France(2010年法国EDF培训课程).pdf
- Training Curriculum on Drug Addiction (培训课程在药物成瘾).pdf
- TRAINING GUIDE Concept2(培训指导Concept2).pdf
- TRAINING OF TRAINERS MANUAL(教练培训手册).pdf
- Training of Trainers SDRG(培训培训师SDRG).pdf
- Training Program Design Template Guide Sample(培训项目设计模板标样).pdf
- Training translators to work for the EU (翻译为欧盟工作培训).pdf
- Training Units listed by Curriculum Pack (培训单位列出的课程包).pdf
- Training with the LTPRO laserlyteimages(培训与LTPRO laserlyteimages).pdf
- TraintheTrainer Manual Chicago State (芝加哥TraintheTrainer手动状态).pdf
文档评论(0)