碗口式满堂脚手架验收分析（Analysis of bowl shaped scaffold acceptance）.docVIP

下载本文档

1
0
约5.4千字
约 8页
2017-09-05 发布于河南
举报
版权申诉

碗口式满堂脚手架验收分析（Analysis of bowl shaped scaffold acceptance）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

碗口式满堂脚手架验收分析（Analysis of bowl shaped scaffold acceptance）

碗口式满堂脚手架验收分析（Analysis of bowl shaped scaffold acceptance） 1. project overview A cast in place box girder bridge is divided into three parts, the length of 224m, C50 concrete 2095m3, span combination (3 * 20+4 * 26+3 * 20) M. Box girder height 1.40M, for single box, double chamber, such as height section continuous box girder, the bottom width 10.7m, top width 15.5m. Box girder construction, the use of WKJ bowl buckle support system. 2. initial layout and size of the scaffold 1) force transfer system The bridge bracket with 2 layers of wood as a force transmission system, which in the generous wooden bowl buckle scaffold support, cross section is 12cm * 12cm, along the bridge to the layout, spacing of 0.9m; on a small wooden timbers, cross section is 8cm * 10cm, transverse layout, spacing 0.3m. 2) bracket specifications and spacing The vertical diameter of the steel pipe is 48mm and the wall thickness is 3.5mm. The specific parameters are shown in the following table. The vertical pole adopts 600mm adjustable base and 600mm adjustable support. The specifications include 3000mm, 2400mm, 1800mm and 1200mm. The space arrangement is 0.9m * 0.6m. Two kinds of cross bar specifications for 600mm, 900mm, step distance 1.5m. Section characteristics of steel pipe Diameter (mm) The wall thickness of T (mm) Cross sectional area A (cm2) The radius of gyration (I cm) Flexural strength (Mpa) 483.5, 4.89, 1.58205 3) overall stability assurance measures In order to ensure the stability of the support, the longitudinal bridge and the transverse bridge are arranged at intervals of 3.6 M. Longitudinally, the brace must be provided at the edge of the bracket to ensure the stability of the bracket. The scissors support and the ground plane are 45 degrees, the angle deviation is less than 15 degrees, each place must be fastened with the fastener with the bowl buckle support frame, must go up to the bottom template, down to the ground. The bracket is extended LM outside the box beam width f