0.8mm不锈钢薄板氩弧焊焊接工艺（Argon arc welding technology of 0.8mm stainless steel sheet）.docVIP

下载本文档

3
0
约5.78千字
约 5页
2017-09-05 发布于河南
举报
版权申诉

0.8mm不锈钢薄板氩弧焊焊接工艺（Argon arc welding technology of 0.8mm stainless steel sheet）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

0.8mm不锈钢薄板氩弧焊焊接工艺（Argon arc welding technology of 0.8mm stainless steel sheet）

0.8mm不锈钢薄板氩弧焊焊接工艺（Argon arc welding technology of 0.8mm stainless steel sheet） The welding process of argon arc welding of 0.8MM stainless steel sheet The trial process in a factory with H6645B type fiber drying machine of main parts of large hot compartment panel, encounter any 0. Welding of 8MM thick stainless steel sheet 0Cr18Ni9. The design requirements of large hot compartment with 0. 8mm thick 0Cr18Ni9 material, the front surface of the panel does not allow welding, welding seam side surfaces must be free of depression. Undercut, smooth, no wave distortion defects and the whole panel after welding. Due to the large window insulation thin plate, a large area (3046mm*1352mm*0. 8mm), the sheet specification limits, panel design will be two welds. Therefore, in the process of welding of stainless steel sheet length to resolve not only the quality of the welding seam, but also control the panel after welding deformation. Considering the automatic TIG welding process with one side welding, good welding quality, welding deformation after welding, high efficiency, especially suitable for welding stainless steel weld, decided to adopt the automatic TIG welding of one side welding process to solve 0. Welding 8mm thick 0Cr18Ni9 sheet. 1 test objective In the 0. Process of forming test 8mm thick 0Cr18Ni9 sheet automatic TIG welding side welding, formulate reasonable welding parameters; take proper welding parameters, obtained can meet the design requirements of the weld quality. 2 welding process test 2.1 welding equipment Welding equipment used ARISTO-500 computer control universal welding machine, the welding machine has a stored program memory and welding, and can adjust and optimize the welding parameters in the welding industry at the same time. It is also equipped with pneumatic clamp and the keys with bad copper liner, can obtain high quality welds and deformation control of thin plate after welding. 2.2 preparation before welding In the special control bed materia