供排水管网改造施工组织方案设计书.doc

XX县城区供排水管网改造工程 （三标段） 施 工 组 织 设 计 重庆XX工程有限公司 2012年8月15日 目 录 第一章 工程概况······················································3 给水部分 一、设计依据····························································3 二、采用技术标准、规范················································3 三、工程设计概况·························································3 排水部分 一、工程概况设计依据及采用的技术规范、标准排水设计 一、管道沟槽开挖······················································19 二、机械开挖沟槽时应注意事项·············································19 三、人工开挖时应注意事项·················································20 四、基槽水、导水和排水施工措施··········································20 第七章 安装与敷设·······················································21 一、管道的进场堆放及运输·················································21 二、管道基础不良地段基础处理及垫层施工···································21 三、管道安装施工工艺·····················································21 第八章 井室结构施工····················································28 一、井室砌筑·····························································28 二、应注意的质量问题····················································28 三、井室混凝土结构施工··················································29 四、检查井与管道的连接··················································29 五、质量要求····························································30 第九章 安管的质量标准排水管道施工质量控制措施管材质量要求安管的质量标准GB50289-98）； 2、《室外给水设计规范》（GB50013-2006）； 3、《给水排水管道工程施工及验收规范》（GB50268-2008）； 4、《给水排水构筑物施工及验收规范》（GBJ141-90）； 5、国家现行有关标准、规范和法规。 三、工程设计概况 1、城区给水现状： 铜梁县城区现有西门水厂（规模近期3.5万m3/d，远期7万m3/d）和玄天湖水厂（规模1万m3/d），远期新建琼江水厂（规模5万m3/d），区内供水方案主干管给水厂供水的接口和路线给水管道平差计算结果、工程概况 本工程污水管道的设计纳污范围为铜梁县部分老城区，东至塔山东街，西至八一路、西环路，南至中兴路、中兴东路，北至大北街、铜合路、北环路、滨河东路、滨河西路，占地面积约5km2。污水由截污管道系统收集后进入污水截留干管，送至污水厂处理。 设计依据及采用的技术规范、标准 设计依据 1．与业主签订的设计委托书及合同。 2．《铜梁县城市总体规划》 3．《铜梁县县城控制性详细规划整合（2010）》 4．《重庆市铜梁县城区污水处理工程可行性研究报告》 5．《铜梁县巴川河、淮远河环境综合整治工程竣工图》 6．业主方提供的地形图等相关资料 采用的技术规范、标准 《室外给水设计规范》 （GB50013-2006） 《室外排水设计规范》 （GB50014-2006） 《给水排水工程构筑物结构设计规范》 （GB50069-2002）