电脑辅助工程应用期中报告.pptVIP

F P2 P1 L1 L2 L3 L4 L1 =15 mm; L2 =5 mm; L3 =10 mm; L4 =2.5 mm; Cross-sectional area=20 mm2; Height = 4 mm; Modulus of Elasticity, E=200 GPa; ν=0.29; P1 =1.2 MPa; P2=1MPa; F=100N 題目： 1. Set up 設定參數： (Unit: N-mm) 一、靜力分析 L1 =15 mm; L2 =5 mm; L3 =10 mm; L4 =2.5 mm; → Total Length, L= L1+L2+L3+L4 Cross-sectional area=20 mm2; → A = 20 mm2 Height = 4 mm; → Height, H= 4mm; Width, B= A/H = 5 mm Modulus of Elasticity, E=200 GPa; →200GPa=200E9 N/m2=200E3 N/mm2=200E3 MPa Poissons ratio ν=0.29; P1 =1.2 MPa; P2=1MPa; F=100N Element size, SIZE = 0.5 →定義元素切割的大小，設定0.5讓作用力作用在Node上 FINISH ! Exits normally from a processor /Clear ! Read - Clears the database ! Units: mm, N L1 = 15 ! Length L2 = 5 ! Length L3 = 10 ! Length L4 = 2.5 ! Length L = L1+L2+L3+L4 ! Total Length A = 20 ! Cross-sectional area H = 4 ! Height B = A/H ! Width E = 200E3 ! Youngs modulus 200GPa=200E9 N/m2=200E3 N/mm2=200E3 MPa NU = 0.29 ! Poissons ratio SIZE = 0.5 ! Element size F = 100 ! Point load P1 = 1.2 ! Distributed load 1.2MPa=1.2E6 N/m2=1.2 N/mm2 P2 = 1 ! Distributed load 1MPa=1E6 N/m2=1 N/mm2 一、靜力分析 為了確保一開始是處於begin level，所以先執行FINISH跳出任何模組 /CLEAR是清除資料庫(歸零)的命令，且只有在begin level才可執行/CLEAR命令 一、靜力分析 2. Preprocessing 2-1. Solid Modeling +X -X -Y +Y -Z +Z ANSYS直角座標定義： 模型座標：運用8個Keypoints建立一個立體模型 座標原點 (0,0,0) B H Total Length, L= L1+L2+L3+L4 K1 K2 K3 K4 K5 K6 K7 K8 /PREP7 ! Preprocessing 一、靜力分析 進入preprocessing模組 K, 1, 0, -H/2, -B/2 K, 2, 0, H/2, -B/2 K, 3, 0, H/2, B/2 K, 4, 0, -H/2, B/2 K, 5, L, -H/2, -B/2 K, 6, L, H/2, -B/2 K, 7, L, H/2, B/2 K, 8, L, -H/2, B/2 利用K命令(K, NPT, X, Y, Z - Defines a keypoint)，NPT指keypoint順序編號， X, Y, Z指 Keypoint的為x,y,z座標。 8個Keypoint