笔记主板维修.pptVIP

WIP Repair Board Report WIP Repair Board Report Power sequence * WIP Repair analysis Report 2005/11/5 Issue Open Date: 1上CPU開機正常，插上DVD開機后自動關機. 2量 DVD CNRT (CN20) 偏壓無异常 ,由此確定為工作電壓＋ｖ５ｓ 异常 （偏大),查得Q33为+V5A转为+V5S的芯片，更换后现象依旧，最终确定为+V5A异常。 更换+V5A电原管理芯片(U12)后 ｏｋ。 Analyze process PW00 Issue Description 1PCS Quantity: WIP Source (where) Davos Model S/N WIP Repair Board Report 2005/11/5 Issue Open Date: 1:插AC 后,電流為0.01不起跳,+V5A,+V3A,+V1.5A無產生, ２:用電表測量無電原點短路現象 ３最終發現為+V5AL轉為+V3AL電路有問題,結果為U509.5輸出PIN對地偏壓偏小導至+V3AL不良.. (詳細電路見Davso電路圖第７頁) Analyze process PW00 Issue Description 1PCS Quantity: WIP Source (where) Davos Model S/N 2005/11/5 Issue Open Date: 1:量各腳PIN偏壓正常 , U10 工作電壓+V3S產生 2:S/B 發給U10的PCI_RESET#信號正常,更換U10后無效 3:今排查S/B所發給U10信號都正常,后發現CLK_R3S_SIO14開機 一斷時間后波形變小,CLK偏小. ４:最后追出為U30.52PIN所發出的信號不良造成 Analyze process CO01,CO03,LP01 Not Pass Issue Description 1PCS Quantity: WIP Source (where) Davos Model S/N 2005/11/5 Issue Open Date: 1:上電后,電流０.０６---０.２０A來回跳,+V5A,+V3A,+V1.5A均產生正常. ２:再次量得+V3S,+V1.5S正常,+VCCP無產生,更換U26后無效, ３:后發現+V5S沒產生,導至U26無工作,+vccp無產生,最終查得 +V5A轉為+V5S Fail.更換Q33 ok. Analyze process PW01 Issue Description 1PCS Quantity: WIP Source (where) Davos Model S/N WIP Repair analysis Report 2005/07/19 Issue Open Date: 1插ＡＣ 后，電流為0.32，+V5A,+V3A,+1.5A+2.5 均產生，+VCCP,+VCC_CORE也同時產生且正常。 ２經進一步測量 CLK(U30)正常輸出，發現CPURST, PCIRST 無輸出 ３根據Power sequence 查找有 VR_PWRGD_CK410送入U17PIN1腳 U17PIN4腳無SB_3S_VRMPWRGD送入南橋，確定IC U17坏件，換掉OK Analyze process PW01/DP00 Issue Description 1PCS Quantity: WIP Source (where) Davos Model S/N WIP Repakr Board Report 2005/11/5 Issue Open Date: 1現象︰上電大電流, +VBATP,+V1.5A short,拆其相關