dc的热处理.docVIP

毕业设计（论文）中文摘要 毕业设计（论文）外文摘要 This paper describes the DC53as a new type of cold working die steel was used in a variety of novel high demand,highprecisioninstrumentmanufacturing,astheevlutionofSKD11steel,whichhasallkindsofadvancedequipmet As a new type of cold die steel, composition and its influence is very important, this is mainly about the composition of the DC53 effects, as well as relative to its original body which has better advantages, for DC53, after the heat treatment tempering process also has the very big impact, tempering produced the problem is we mainly analyzed by the analysis, in order to better understand its meaning. At the same time it also to understand why is divided into cold and hot working die steel two kinds, the distinction between what is direction. In the study of these problems while in more comprehensive understanding of the deep meaning of four fire ( heat treatment the most basic of normalizing, annealing, quenching, tempering). At the same time after heat treatment, may appear on the drawing crack of a certain explanation, in order to better guide us Keyword: DC53cold die SDK11tempering 分享到 翻译结果重试 抱歉，系统响应超时，请稍后再试 支持中英、中日在线互译 支持网页翻译，在输入框输入网页地址即可 提供一键清空、复制功能、支持双语对照查看，使您体验更加流畅 目录 1. 引言 4 1.1一种新型的冷作模具材料DC53 4 1.2 模具的基本介绍与成分影响 8 1.3.1 工冷作模具钢与热作模具钢区别 12 1.3.2常见模具钢以及用途介绍 13 1.3.3冷却模具钢种分类依据 16 1.3.4充分发挥冷作模具钢性能潜力的途径 17 1.4论文的目的与意义 18 2.设备相关 18 2.1井式炉 18 2.2箱式炉 19 2.3多用炉 19 3.DC53的热处理工艺 21 3.1 DC5的预热处理工艺 21 3.2DC53的工艺曲线 27 3.3SKD11的热处理工艺以及与DC53的比较 30 4回火脆性问题与解决方案 32 5 DC53的拉丝慢裂的相关 34 结论 35 致 谢 37 参考文献 38 1. 引言 1.1一种新型的冷作模具材料DC53 DC53作为一种新型的冷作模具钢种，在国内的国内牌号为Gr8Mo2SiV，6000C回火硬度下降仅为HRC52.4，所以温度不能过高，5200C左右硬度峰值，5000C冲击韧性差，表性一定的高温回火脆性，6000C冲击韧性很好，但应诉下降.达不到使用要求 DC53（SLD8）冷冲模合金钢 其性能有：冲裁模、冷作成形模、深拉模、成形轧辊、冲头（高温回火后硬度可达HRC60或以上，并有利于线切割加工） DC53模具钢材是对SKD11进行改良的新型冷作模具钢，其技术规范载于日本工业标准（JIS）G4404。它克服了SKD11高温回火硬度和韧性不足的弱点，将在通用及精密模具领域全面取代SKD11。 其韧性是SKD11的2倍，DC53的韧性在冷作模具钢中较为突出。特宝金属提供图案 用DC53制造的工具很少出现裂纹和开裂，大大提高了使用寿命与此同时DC53之三个优良特性(1)DC5