单区域OSPF的调整和排错AdjustandTroubleshootSingle-AreaOSPF.PPT

下载文档 降价啦

29
0
约2.74万字
约 76页
2017-11-17 发布于天津
举报
版权申诉
保障服务

单区域OSPF的调整和排错AdjustandTroubleshootSingle-AreaOSPF.PPT

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。

单区域OSPF的调整和排错AdjustandTroubleshootSingle-AreaOSPF

* * * 5.1 Advanced Single-Area OSPF Implementations 5.1.1 OSPF in Multiaccess Networks 5.1.1.6 Default DR/BDR Election Process 3 ways to determine router ID: Router ID can be manually configured. If not configured , ID determined by highest loopback IP address. If no loopbacks, ID is determined by the highest active IPv4 address. * * 5.1 Advanced Single-Area OSPF Implementations 5.1.1 OSPF in Multiaccess Networks 5.1.1.7 DR/BDR Election Process * * 5.1 Advanced Single-Area OSPF Implementations 5.1.1 OSPF in Multiaccess Networks 5.1.1.7 DR/BDR Election Process * * 5.1 Advanced Single-Area OSPF Implementations 5.1.1 OSPF in Multiaccess Networks 5.1.1.7 DR/BDR Election Process * * * 5.1 Advanced Single-Area OSPF Implementations 5.1.1 OSPF in Multiaccess Networks 5.1.1.8The OSPF Priority 5.1.1.9 Changing the OSPF priority * * * 5.1 Advanced Single-Area OSPF Implementations 5.1.2 Default Route Propagation 5.1.2.1 Propagating a Default Static Route in OSPFv2 The router connected to the Internet used to propagate a default route –often called the edge, entrance or gateway router –in an OSPF network is also called the autonomous system boundary router (ASBR). To propagate the route: * * 5.1 Advanced Single-Area OSPF Implementations 5.1.2 Default Route Propagation 5.1.2.2 Verifying the Propagated Default Route * * 5.1 Advanced Single-Area OSPF Implementations 5.1.2 Default Route Propagation 5.1.2.3 Propagating a Default Static Route in OSPFv3 5.1.2.4 Verifying the Propagated IPv6 Default Route * * 5.1 Advanced Single-Area OSPF Implementations 5.1.2 Default Route Propagation 5.1.2.3 Propagating a Default Static Route in OSPFv3 5.1.2.4 Verifying the Propagated IPv6 Default Route * * 5.1 Advanced Single-Area OSPF Implementations 5.1.3 Fine-tuning OSPF Interfaces 5.1.3.1 OSPF Hello and Dead Intervals OSPF Hello and Dead intervals must match or a neighbor adjacency does not occur. * * 5.1 Advanced Single-Area OSPF Implementations 5.1.3 Fine-tuning OSPF Interfaces 5.1.3.2 M