LCD12864 串行程序.docVIP

LCD12864 串行程序 #include pic.h #define uchar unsigned char __CONFIG(0x3F72); //关程序保护，关LVP，开BROWN——out，外部晶振高速，关看门狗， #define LCD_CS RB4 #define LCD_SID RB5 #define LCD_SCLK RB6 #define LCD_CS_OUT TRISB4 = 0 #define LCD_SID_OUT TRISB5 = 0 #define LCD_SCLK_OUT TRISB6 = 0 #define LCD_SID_IN TRISB5 = 1 #define WRITE_COMMAND 0xf8 #define WRITE_DATA 0xfa /********在基本指令集下的指令********************/ #define CLEAN_SCREEN 0x01 //清屏函数 0000 0001 #define HOME 0x02 //位址归位 0000 0010 #define DISPLAY_ON 0x0c //开游标，开显示 0000 1110 #define CURSOR 0x1a /***********基本，扩充指令集切换函数***************/ #define open_extend 0x34 //开启扩充指令集 ，关闭绘图功能 #define close_extend 0x30 //开启基本指令集 #define open_drawing 0x36 //开启绘图功能 #define close_drawing 0x34 //关闭绘图功能 const uchar digital[]={0x30,0x31,0x32,0x33,0x34,0x35,0x36,0x37,0x38,0x39}; const uchar ENGLISH[]={0x41,0x42,0x43,0x44,0x45,0x46,0x47,0x48,0x49,0x4a,0x4b,0x4c,0x4d,0x4e,0x4f,0x50,0x51,0x52,0x53,0x54,0x55,0x56,0x57,0x58,0x59,0x5a}; //写指令起始 1111 1000=0xf8 写数据 1111 1010=0xfa void loction(uchar x, uchar y); void LCD_delay(uchar x) { uchar i,j,z; for(i = x;i0;i--) for(j = 5;j0;j--) for(z=100;z0;z--); } /************液晶写指令函数********************/ void LCD_wtite(uchar description, uchar data) { uchar H_data,L_data,i; LCD_CS_OUT; LCD_SID_OUT; LCD_SCLK_OUT; LCD_CS = 1; LCD_delay(1); for(i=0;i8;i++) //这里写一个起始字节 { if(description0x80) LCD_SID = 1; else LCD_SID = 0; LCD_delay(1); description =1; LCD_SCLK = 0; LCD_SCLK = 1; //由低到高的时候，提取数据 } H_data =data 0xf0; //因为ST7920的特殊性，一个字节要改成两个字节传送，所以这里将第四位变成0 L_data =data 0x0f; L_data = 4; for(i=0;i8;i++) //这里写数据 { if(H_data0x80) LCD_SID = 1; else LCD_SID = 0; LCD_delay(1); H_data =1; LCD_SCLK = 0; LCD_delay(1); //SCL低电平的时候，运行数据变化 LCD_SCLK = 1; LCD_delay(1); //由低到高的时候，提取数据 } for(i=0;i8;i++) //这里写数据 { if(L_data0x80) LCD_SID = 1; else LCD