F360最小系统测试程序.docx

/************************************************* 功能：F360最小系统测试程序12864开机时显示键盘显示测试程序和正弦波形；每按一个按键，LCD上显示相应字符；P2.0~P2.7显示不同频率的方波；IDA0产生锯齿波。*************************************************/#include C8051F360.H#define uchar unsigned char#define uint unsigned int#define ulong unsigned long#define CS1 0x4000 //外部扩展片选地址1#define CS2 0x8000 //外部扩展片选地址2#define LEDENCS 0xC004 //LCD模块背光控制片选信号#define WCOMADDR 0xC008 //写命令寄存器的地址#define WDATADDR 0xC009 //写数据寄存器的地址#define RCOMADDR 0xC00A //读命令寄存器的地址#define RDATADDR 0xC00B //读数据寄存器的地址#define KEYCS0xC00C //读键盘的地址uchar count1;//软件计数器uchar keycode;//存放键值uchar LEDCON=0x00;//LCD模块背光控制字，最低位为0时关LED背光，最低位为1时开启LED背光，uchar idata WaveData[128]; //波形数据缓冲区 bitkeysign=0; //键标志，0：无键输入，1：有键输入sbit START=P3^0;sbit SW0=P3^1;sbit SW1=P3^3;uchar code hanzi10[] = 键盘显示测试程序;uchar code hanzik0[] = K0;uchar code hanzik1[] = K1;uchar code hanzik2[] = K2;uchar code hanzik3[] = K3;uchar code hanzik4[] = K4;uchar code hanzik5[] = K5;uchar code hanzik6[] = K6;uchar code hanzik7[] = K7;uchar code hanzik8[] = K8;uchar code hanzik9[] = K9;uchar code hanzika[] = KA;uchar code hanzikb[] = KB;uchar code hanzikc[] = KC;uchar code hanzikd[] = KD;uchar code hanzike[] = KE;uchar code hanzikf[] = KF;uchar code sindata[128]={ 0x80,0x86,0x8c,0x92,0x98,0x9f,0xa5,0xab,0xb0,0xb6,0xbc,0xc1,0xc7,0xcc,0xd1,0xd5, 0xda,0xde,0xe2,0xe6,0xea,0xed,0xf0,0xf3,0xf6,0xf8,0xfa,0xfc,0xfd,0xfe,0xff,0xff, 0xff,0xff,0xff,0xfe,0xfd,0xfc,0xfa,0xf8,0xf6,0xf3,0xf0,0xed,0xea,0xe6,0xe2,0xde, 0xda,0xd5,0xd1,0xcc,0xc7,0xc1,0xbc,0xb6,0xb0,0xab,0xa5,0x9f,0x98,0x92,0x8c,0x86, 0x7f,0x79,0x73,0x6d,0x67,0x60,0x5a,0x54,0x4f,0x49,0x43,0x3e,0x38,0x33,0x2e,0x2a, 0x25,0x21,0x1d,0x19,0x15,0x12,0x0f,0x0c,0x09,0x07,0x05,0x03,0x02,0x01,0x00,0x00, 0x00,0x00,0x00,0x01,0x02,0x03,0x05,0x07,0x09,0x0c,0x0f,0x12,0x15,0x19,0x1d,0x21, 0x25,0x2a,0x2e,0x33,0x38,0x3e,0x43,0x49,0x4f,0x54,0x5a,0x60,0x67,0x6d,0x73,0x79,