原创力文档- 1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
- 2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击 这里二次下载。
- 3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
- 4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
- 5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
- 6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
- 7、VIP文档为合作方或网友上传，每下载1次， 网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档
查看更多
毕业设计（论文）-塑件工艺分析及结构设计
目 录
第一章 概论 ·················································· 1
1.1 注射模塑原理 ·············································· 1
1.2 塑件的工艺性分析 ·········································· 1
1.3 塑料件的设计原则 ·········································· 1
1.4 塑料制件的选材 ············································ 2
1.5 塑件工艺分析及结构设计 ···································· 2
第二章 模塑工艺规程的编制 ································· 3
2.1 塑件的工艺性分析 ·········································· 4
2.2 计算塑件的体积和重量 ······································ 4
2.3 塑件注塑工艺参数的确定 ···································· 5
第三章 注射模的结构设计 ···································· 5
3.1 分型面选择 ················································ 5
3.2 确定型腔的排列方式 ········································ 6
3.3 浇注系统设计 ·············································· 6
3.4 侧向分型机构设计 ··········································· 8
第四章 模具设计的有关计算 ·································· 13
4.1 型腔和型芯工作尺寸计算 ··································· 13
4.2 型腔侧壁厚度和底板厚度计算 ······························· 17
4.3 模具加热和冷却系统的计算 ································· 18
第五章 模具主要零件的设计及选用 ··························· 20
5.1 标准模架的选用 ··········································· 20
5.2 浇口套的设计 ············································· 21
5.3 推杆的选用 ··············································· 22
5.4 弹簧的选用 ··············································· 23
第六章 模具参数的相关校核 ································· 24
6.1 注塑机最大注塑量校核 ····································· 24
6.2 与注塑机拉杆面积的校核 ··································· 24
6.3 模具闭合高度校核 ········································· 24
6.4 开模行程校核 ············································· 24
第七章 绘制模具的总装图和非标零件图 ······················ 25
第八章 模具的装配工艺 ····································· 26
8.1 模具的装配方法·············································· 26
8.2
文档评论（0）