单片机_频率计.docxVIP

单片机——频率计设计作者：Aikundechong附件3：频率计源程序#include reg52.h#defineSegmentP2#define sl P0sbit addr0=P1^0; //定义数据端口地址，000时16分频，100不分频sbit addr1=P1^1;sbit addr2=P1^2;sbit clear=P1^3; //计数器清零sbit ledM=P1^4; //档位led显示sbit ledK=P1^5;sbit ledB=P1^6;unsigned char cnt; //定时1s计数unsigned char d[4]; //对应数码管的各位unsigned char level; //档位unsigned int tN; //不同档位计时值unsigned int fCnt; //脉冲下降沿次数unsigned int regCnt; //脉冲次数暂存unsigned int pCnt; //频率显示unsigned char Num[10]={0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d,0x07,0x7f,0x6f};void Delay(unsignedintDelayTime){while(DelayTime--);}void disp(){if(level==0) //B位档{d[3]=0;d[2]=pCnt/100;d[1]=(pCnt%100)/10;d[0]=pCnt%10;sl=0xfe;Delay(1);Segment=Num[d[3]];Delay(300);sl=0xfd;Delay(1);Segment=Num[d[2]];Delay(300);sl=0xfb;Delay(1);Segment=Num[d[1]];Delay(300);sl=0xf7;Delay(1);Segment=Num[d[0]];Delay(300);}else if(level==1){d[3]=pCnt/1000;d[2]=(pCnt%1000)/100;d[1]=(pCnt%100)/10;d[0]=pCnt%10;sl=0xfe;Delay(1);Segment=Num[d[3]];Delay(300);sl=0xfd;Delay(1);Segment=Num[d[2]];Delay(300);sl=0xfb;Delay(1);Segment=Num[d[1]]+0x80;Delay(300); //带小数点sl=0xf7;Delay(1);Segment=Num[d[0]];Delay(300);}else if(level==2){d[3]=pCnt/1000;d[2]=(pCnt%1000)/100;d[1]=(pCnt%100)/10;d[0]=pCnt%10;sl=0xfe;Delay(1);Segment=Num[d[3]]+0x80;Delay(300);sl=0xfd;Delay(1);Segment=Num[d[2]];Delay(300); //带小数点sl=0xfb;Delay(1);Segment=Num[d[1]];Delay(300); sl=0xf7;Delay(1);Segment=Num[d[0]];Delay(300);}else{d[3]=0;d[2]=0;d[1]=0;d[0]=0;}}void intial(){clear=1; //分频器初始化addr0=0;addr1=0;addr2=1;tN=20; //档位初始化为Hz档level=0;ledM=1; //显示Hz档ledK=1;ledB=0;TMOD=0x61; //定时器0，工作方式1，计数器1，工作方式2(8位自动重装)TH0=(65536-50000)/256; //计数50msTL0=(65536-50000)%256; TH1=256-1; //计数器1计数初值TL1=256-1;TR0=1; //开定时器0中断ET0=1; //定时器0允许TR1=1; //开计数器1中断ET1=1; //允许计数器1中断EA=1; //总中断允许}void main(){intial();while(1){disp();}}void timer0() interrupt 1{cnt++;if(cnt==tN){ET1=0; //计时