机制课程设计说明书--(手压阀).docVIP

机制课程设计说明书 题 目： 手压阀 院 （部）： 机电工程学院 专 业： 机电工程及自动化 班 级： 机械XX 姓 名： XXX 学 号： XXXXXXXXX 指导教师： XXXXXXX 完成日期： 2010年7月7日 目 录 1 任 务······························································ 1 2 典型零件AutoCAD图纸 2.1主视图·······························································2 2.2俯视图·······························································2 2.3 左视图·······························································2 3典型零件造型设计····················································3 4其他零件设计 4.1 轴···································································7 4.2 托架·································································8 4.3 垫片·································································8 4.4 填料压盖·····························································9 5装配效果图···························································9 6 CAXA制造工程师 6.1 加工对象的加工造型··················································10 6.2生成刀具轨迹························································10 6.3知识加工轨迹明细单··················································12 谢 辞·································································13 参考文献·······························································13 附 录·································································14 1 任 务 了解手压阀的相关原理、组成，并查找相关资料，设计相应的零部件结构或机构，实现手压阀的基本功能要求。(一)手压阀装配的手工绘图、以及塞座、阀体等二维图设计和手工绘制图。选择典型零件进行工艺分析，编写机械加工工艺过程卡片，用CAXA制造工程师进行造型设计，并生成刀具轨迹及加工仿真。(二)对手压阀塞座和阀体的造型设计进行创新及改进，在造型设计中，要求使用尽可能少的命令来达到最佳的设计效果，设计的零件占用的计算机内存尽可能的少。在装配过程中，选择最佳的装配过程及步骤，以满足手压阀的基本功能要求，并进行三维实体的渲染、零件的干涉检查等，具体时间安排详见任务书。 本课程设计在机械设计课程设计基础之上运用Solid Edge三维造型、CAXA制造工程软件对所设计的手压阀进行三维建模，并通过CAXA制造工程师进行进行造型设计，并生成刀具轨迹及加工仿真。意义重大，机会难得，故需好好把握！ 2典型零件AutoCAD图纸 2.1 主视图 2.2 俯视图 2.3 左视图 3典型零件造型设计 塞座零件设计 1 首先打开Solid EdgeV16程序并点击草图，然后选择X-Y平面，在建模窗口中绘制正六边形，图形如下： 点击完成草图。然后选择拉伸命令，输入拉伸长度12，结果图形如下： 3点击草图，选择平行平面，绘制如图所示的草图，结果图形如下： 4点击旋转除料命令，输入360°，点击完成，结果图形如下： 5 点击草图命令，选取重合平面建立草图，画完后拉伸长度为3，结果图形如下： 6同样点击草图命令，选取重合平面之拉伸体3的上表面画直径为44的圆，画完后拉伸长