我的毕业的设计 50t成型线圈热压机液压系统的设计.docVIP

我的毕业设计 50t成型线圈热压机液压系统设计 摘要 此毕业设计完成的是对成型线圈热压机液压系统的液压设计。成型线圈热压机设备的作用是确保梭形线圈的各部尺寸满足线圈的设计要求，提供下线的工艺水平，并通过对经压制后的线圈各部尺寸的测量，使其各项尺寸基本满足了设计与工艺的要求。它先将压型机上、下工作台及胎具进行加热，待达到工作温度后，将几组制好的线圈与胎具放入工作台上。根据圈的尺寸，调整好上油缸与侧压缸的工作压力。上工作台下压，当压到工件，上工作台再抬起一定的间隙，然后，使侧压缸压紧线圈，最后将上工作台压紧工件，并保压一段时间。在加工中，有快进、快退对整个系统会产生很大的压力脉冲。为了实现对液压缸，整个系统机构保压稳压的效果，采用了较小的流量规格的蓄能器。当泵的流量进入蓄能器被储存起来，吸收系统部分脉动缓冲和液压冲击。 关键词：加压、快进、侧压 The graduation project is completed by forming the coil hot press hydraulic hydraulic system design.Hot press forming coil device is to ensure the spindle coil winding ministries to meet the design requirements of size,technological level to provide off the assembly line,and through the post by thesuppression of measuring the size of the coil ministries,to meet the basic size Design and technologyrequirements.It is first pressure-type machine,the next table and the mold is heated until the temperature reached after several groups of the system will be agood coil and mold into the table.According to ring size,adjust the cylinder on the cylinder and lateral pressure of work.Pressure on the work of the audience,when the pressure to the workpiece,the table and then lift some of the gap,then,to compress the coil side pressure cylinder,and finally compress the workpiece on the table,and holding pressure time.In the process,there is fast forward,rewind the whole system will have alot of pressure pulses.In order to achieve the hydraulic cylinder,the whole system the effect of institutional holding pressure regulator,using the smaller size of the accumulator flow.When the pump flow into the accumulator is stored,the buffer absorption system pulsation and hydraulic shock some.Key words：pressure,fast-forward,lateral pressure前言 大中型电机下线用梭形线圈经绕制的直线度及线圈的截面尺寸很难保证技术要求，必须经热压固化成型后才能顺利地进行下线，而压制的线圈截面尺寸是成型的关键，压制这类线圈，最好的是制造一种专用设备来完成。 目前，一些厂家基本是采用v型铁加热，放上一只线圈和胎具后，靠手动螺旋夹紧，有时由于v型铁受热变形，造成温度不均。手动螺旋夹紧，夹紧力部好测定，压制的线圈质量不稳定，为了确保梭形线圈的各部尺寸满足线圈的设计要求，提供下线的工艺水平，我们研究设计制造了成型线圈热压型机。通过对经压制后的线圈各部尺寸的测量，其各项尺寸基本满足了设计与工艺的要求。本机械设备采用了液压传动系统，液压传动