日本验船师全套培训资料Welding(Procedure).pptVIP

下载本文档

4
0
约1.69千字
约 33页
2018-06-09 发布于浙江
举报
版权申诉

日本验船师全套培训资料Welding(Procedure).ppt

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

日本验船师全套培训资料Welding(Procedure)

Welding (Procedure) September 2004 Edge preparation for butt joint (1/5) Edge preparation for butt joint (2/5) Edge preparation for butt joint (3/5) Edge preparation for butt joint (4/5) Edge preparation for butt joint (5/5) Special requirements for fillet welding Special requirements for fillet welding Special requirements for fillet welding Special requirements for fillet welding Special requirements for fillet welding Special requirements for fillet welding Special requirements for fillet welding Slot weld Joint of cast/forged steel Joint of plate to cast/forged steel Basic welding sequence (1/3) Basic welding sequence (2/3) Basic welding sequence (3/3) Welding sequence of plates (1/2) Welding sequence of plates (2/2) Welding sequence at “T” joint (1/2) Welding sequence at “T” joint (2/2) Example of joint with web and face Welding sequence for web and face Kind of scallop Block joint of longitudinal member Welding sequence for collar plate Welding sequence for closing hole (1/2) Welding sequence for closing hole (2/2) Welding sequence for partial renewal Welding sequence for closing access hole 　　千鳥断続隅肉溶接（staggered intermittent fillet weld） X開先で溶接部が交差する場合には、一方向の両面が完了後に他方向の溶接を始める板厚16mm未満はV、それ以上はX開先通常は横方向→縦方向の順に溶接する溶接熱による変形、亀裂防止のために、スライドのような手順を採用する * * Thickness is 6mm or less Thickness is more than 6mm Difference in thickness is 3mm or less Difference in thickness is more than 3mm One side welding High stress area Otherwise, staggered intermittent fillet weld Hold frames of bulk carrier End connections of section bar (F1) Bilge keel Stringer plate sheer strake Tubular pillar end Thickness is 25 mm or less Thickness is more than 25 mm * Welding (Procedure)