lcd1602程序.doc

lcd1602程序 作者：佚名 文章来源：internet 点击数：233 更新时间：2006-7-7 #includereg52.h#define uchar unsigned char#define uint unsigned intsbit LCM_RW=P2^6; //定义引脚sbit LCM_RS=P2^7;sbit LCM_E=P2^5;#define LCM_Data P0#define Busy 0x80 //用于检测LCM状态字中的Busy标识 void WriteDataLCM(unsigned char WDLCM);void WriteCommandLCM(unsigned char WCLCM,BuysC);unsigned char ReadDataLCM(void);unsigned char ReadStatusLCM(void);void LCMInit(void);void DisplayOneChar(unsigned char X, unsigned char Y, unsigned char DData);void DisplayListChar(unsigned char X, unsigned char Y, unsigned char code *DData);void Delay5Ms(void);void Delay400Ms(void); unsigned char code cdle_net[] = {};unsigned char code email[] = {ky3344@163.com}; void main(void){Delay400Ms(); //启动等待，等LCM讲入工作状态LCMInit(); //LCM初始化Delay5Ms(); //延时片刻(可不要) DisplayListChar(0, 0, cdle_net);DisplayListChar(0, 1, email);while(1);} //写数据void WriteDataLCM(unsigned char WDLCM){ReadStatusLCM(); //检测忙LCM_Data = WDLCM;LCM_RS = 1;LCM_RW = 0;LCM_E = 0; //若晶振速度太高可以在这后加小的延时LCM_E = 0; //延时LCM_E = 1;} //写指令void WriteCommandLCM(unsigned char WCLCM,BuysC) //BuysC为0时忽略忙检测{if (BuysC) ReadStatusLCM(); //根据需要检测忙LCM_Data = WCLCM;LCM_RS = 0;LCM_RW = 0; LCM_E = 0;LCM_E = 0;LCM_E = 1; } //读数据unsigned char ReadDataLCM(void){LCM_RS = 1; LCM_RW = 1;LCM_E = 0;LCM_E = 0;LCM_E = 1;return(LCM_Data);} //读状态unsigned char ReadStatusLCM(void){LCM_Data = 0xFF; LCM_RS=0;LCM_RW = 1;LCM_E = 0;LCM_E = 0;LCM_E = 1;while (LCM_Data Busy); //检测忙信号return(LCM_Data);} void LCMInit(void) //LCM初始化{LCM_Data = 0;WriteCommandLCM(0x38,0); //三次显示模式设置，不检测忙信号Delay5Ms(); WriteCommandLCM(0x38,0);Delay5Ms(); WriteCommandLCM(0x38,0);Delay5Ms(); WriteCommandLCM(0x38,1); //显示模式设置,开始要求每次检测忙信号WriteCommandLCM(0x08,1); //关闭显示WriteCommandLCM(0x01,1); //显示清屏WriteCommandLCM(0x06,1); // 显示光标移动设置WriteCommandLCM(0x0C,1); // 显示开及光标设置} //按指定位置显示一个字符void DisplayOneChar(unsigned char X, unsigned char Y, unsigned char DData){Y = 0x1;X = 0xF; //限制X不能大