引线片的毕业设计--引线片冲裁件冲裁工艺及模具设计.docxVIP

目录摘要3Abstract41 、绪论52、零件工艺性分析72.1 零件要求72.2 材料分析82．3 结构分析82.4 精度分析83、工艺方案及工艺计算93.1工艺方案确定93.2工艺计算9（1）排样设计9（2）冲裁工艺力的计算113.3初选压力机124 、模具的总体设计134.1 模具类型的选择134.2 操作方式134.3 卸料、出件方式13（1）卸料方式13（2）出件方式134.4确定送料方式134.5确定导向方式145 、模具零件设计及标准件的选择155.1 工作零件设计15（1）模具间隙15（2）落料凹模和冲孔凸模刃口的制造公差15（3）冲孔凸模16（4）凹模采用整体式结构185.2 其他板类零件的设计185.3 橡胶的选用19（1）根据卸料力求橡胶的横截面积19（2）橡胶的高度尺寸19(3)校核205.4 模柄的选用205.5 导柱与导套的选择205.6 紧固零件的选择205.7 所选设备的校核206 、模具总装图217 、模具零件加工工艺238 、模具的装配26设计总结28致谢29参考文献30摘要本设计题目为引线片冲裁模，体现了典型冲裁模的设计要求、内容及方向，有一定的设计意义。通过对该模具的设计，加强了设计者对冲裁模设计基础知识的理解和运用，为设计更复杂的冲裁模具做好了铺垫。本设计运用冲裁工艺及模具设计的基础知识，首先分析了板材的性能要求，为选取模具的类型做好了准备；然后计算了冲裁件的冲裁力，便于选取压力机吨位及确定压力机型号；最后分析了冲裁件的特征，便于确定模具的设计参数、设计要点及卸件装置。本设计采用了冲孔—落料级进模成形引线片。成形原理可划分为两个阶段：首先冲孔凸模与凹模共同作用先冲出两个1.85mm和两个6.5mm的孔，而后利用第一步冲出的两个1.85mm和两个6.5mm的孔做精确定位使外形凸模与凹模共同作用使工件落料成形。关键词冲孔—落料级进模,冲孔凸模,凹模,压力机吨位AbstractThe topic for the design is gasket blanking die design,It has manifested the typical blanking dies design request, the content and the direction, has certain design significance.Through the design of the component mold, strengthens the designer’s understand and utilize to the blanking die design basical knowledge,has prepareed for designing more complex blanking die.The design has utilize blanking craft and the basical knowledge of the mold design, has first analyzed the property requirement of the plate , has prepared for selecting the mold type；then has calculated the blanking strength,has advantaged to select the press tonnage and determine press model; Finally has analyzed the characteristic of the products, has advantaged to finite the mold design variable,the design main point and shedder. This design used piercing and blanking progressive die to form the products.The forming principle can be divided to two stages: First, piercing punch and die affect together and pierce two holes of1.85mm and two holes of6.5mm,then use the three holes as pinpoint to make the product formed.Key word Piercing and blanking progressive die Piercing punch Pr