嵌入式C语言程序设计 使用MCS-51EX5-7.doc

童梦无忧网 试管婴儿论坛 本文由壹个坏孩子贡献 /* 标题：范例 5-7 版本：1.0 Target：89S51 程序描述：这个程序利用89X51连接绘图型LCD，然后显示出： 现在时间是： 12：30：00 /05/09/01 */ /* ***************************************************** */ #include REGX51.H /* 绘图型LCD 指令 */ #define GLCD_OFF 62 //关闭绘图型LCD #define GLCD_ON 63 //打开绘图型LCD #define GLCD_START_LINE_0 192 //设定绘图型LCD左半边的起始行 #define SET_PAGE 184 //设定绘图型LCD的页数 #define SET_Y_ADDRESS_0 64 //设定绘图型LCD的y轴位置 #define CLEAR 0 //清除绘图型LCD /* 绘图型LCD 控制线 */ #define ENABLE 1 #define DISABLE 0 #define READ 1 #define WRITE 0 #define COMMAND 0 #define DATA 1 #define GLCD_RESET P2_2 #define GLCD_CS2 P2_3 #define GLCD_CS1 P2_4 #define GLCD_D_I P2_5 #define GLCD_R_W P2_6 #define GLCD_ENABLE P2_7 typedef struct { char hour; char minute; char second; } time; typedef struct { char year; char month; char day; } date; time now; date today; unsigned char gx,gy; static unsigned timer0_tick; char code int2char[]=0123456789; char code monthday[]={31,28,31,30,31,30,31,31,30,31,30,31}; char code weekday[7][4]={MON,TUE,WED,THU,FRI,SAT, SUN}; unsigned char code digit[10][4][8]= //０ {{ {0X00,0X00,0X00,0XFC,0XFE,0X03,0X01,0X81}, {0XC1,0X61,0X31,0X1B,0XFE,0XFC,0X00,0X00}, {0X00,0X00,0X00,0X0F,0X1F,0X36,0X23,0X21}, {0X20,0X20,0X20,0X30,0X1F,0X0F,0X00,0X00}}, //１ { {0X00,0X00,0X00,0X00,0X00,0X04,0X06,0XFF}, {0XFF,0X00,0X00,0X00,0X00,0X00,0X00,0X00}, {0X00,0X00,0X00,0X00,0X20,0X20,0X20,0X3F}, {0X3F,0X20,0X20,0X20,0X00,0X00,0X00,0X00}}, //２ { {0X00,0X00,0X00,0X1C,0X1E,0X03,0X01,0X81}, {0XC1,0X41,0X61,0X33,0X3E,0X1C,0X00,0X00}, {0X00,0X00,0X00,0X3C,0X3E,0X33,0X31,0X31}, {0X30,0X30,0X30,0X30,0X30,0X3C,0X00,0X00}}, //３ { {0X00,0X00,0X00,0X0C,0X0E,0X02,0X01,0X41}, {0X41,0XE1,0XE1,0XB2,0X1E,0X0C,0X00,0X00}, {0X00,0X00,0X00,0X0C,0