毕业设计说明_塑料弯管注射模具设计.docxVIP

[键入文字]毕业设计说明书塑料弯管注射模具设计学生姓名： 学号： 学 院： 专 业： 指导教师： 年月中北大学2013届毕业设计说明书塑料弯管注塑模具设计摘要本文研究的是90带螺纹的塑料弯管及其注射成型的总体设计过程。弯管成90直角，因此侧向分型抽芯是研究的重点。塑料弯管上有一段螺纹，本研究采用的是比较简单轻便的设计模式，因此采取了瓣合模的成型方式。因为不使用复杂的脱螺纹装置，这一点对于螺纹类的制品具有指导意义。本文选择了正确的注塑机型号，采用PROE进行模具的体积确定与分型面的选择，决定采取一模四腔的方式，这将会快速的提高生产量与生产效率。本研究成功设计，将会为以后的弯管类塑料提供极高的参考价值，并且对于生产有很高的经济效益。关键词：塑料弯管，侧向分型抽芯，瓣合模Plastic pipe injection mold designAbrtractThis paper studies a 90-degree bend with thread and plastic injection mold of design process.The bend has a 90-degre .So the focus of the study is side parting core pulling.There was a thread on plastic pip.This study uses a simple design patterns.So flap spotting is the better method .Because which avoid the complex the installation of the unscrewing,which gives a guiding significance for the products of thread. By selecting the right injection molding machine type.Using PROE determine the volume of the mold and parting line selection.It is to decide taking a mold with a four cavity, which would rapidly increase the production capacity and production efficiency.Successful design of this study will be for the future of plastic pipe classes provide a high reference value, and for the production of high economic efficiency. Key words:plastic pipe,side parting core pulling,flapclamping PAGE \* MERGEFORMAT IV目录 TOC \o 1-3 \h \z \u HYPERLINK \l _Toc359419748 1 前言 PAGEREF _Toc359419748 \h 1HYPERLINK \l _Toc359419749 2塑件结构与原材料工艺分析 PAGEREF _Toc359419749 \h 3HYPERLINK \l _Toc359419750 2.1 带螺纹塑料弯管的设计 PAGEREF _Toc359419750 \h 3HYPERLINK \l _Toc359419751 2.1.1 塑料弯管的立体示意图 PAGEREF _Toc359419751 \h 3HYPERLINK \l _Toc359419752 2.1.2 塑料弯管的二维视图 PAGEREF _Toc359419752 \h 3HYPERLINK \l _Toc359419753 2.1.3 塑料弯管的结构尺寸特征分析 PAGEREF _Toc359419753 \h 3HYPERLINK \l _Toc359419754 2.2 塑料弯管原材料的选择分析 PAGEREF _Toc359419754 \h 4HYPERLINK \l _Toc359419755 2.2.1 塑料的原材料的选择 PAGEREF _Toc359419755 \h 4HYPERLINK \l _Toc359419756 2.2.2 硬质聚氯乙烯的性能指标