加工中心全部地报警说明.docVIP

FANUC 警报讯息说明 2007/2/12Page:1/5项次警 报 讯 息说 明处 理 方 法11000 DOOR NOT CLOSE CAN NOT START安全门未关不能启动关闭前门21001 CHECK POT UP LSSOL刀套未在水平位置检查刀套上开关及电磁阀31002 Z AXIS NOT IN 2 POSITIONZ轴未在换刀点位置上重新校验Z轴换刀高度41003 Z AXIS CANCELLEDZ轴取消检查Z轴取消情况51004 ATC NOT READYATC未准备完成a.检查主轴是否在夹刀状态及开关是否正常b.检查刀臂是否在原点位置及原点开关是否正常61005 ARM RUN OVER TIME刀臂换刀超过时间检查热继电器是否跳脱71006 TOOL NO. NOT SETTING刀具号码不在数据表上81007 ATC LS. FAILURE刀臂上开关故障91008 CHECK POT DOWN LSSOL检查刀套下开关及电磁阀检查刀套下开关及电磁阀101009 OIL COOLER FAILURE主轴油冷警报检查油面高度及压力开关111010 CHECK TOOL UNCLAMP LS检查主轴松刀开关检查主轴松刀开关121011 CHECK TOOL CLAMP LS检查主轴夹刀开关检查主轴夹刀开关131012 CHECK ARM BRAKE SENSOR 1 MS.OL检查刀臂煞车点开关检查刀臂煞车点开关141013 4TH AXIS CLAMPED第四轴在夹的状态151014 CHECK ARM U/C SENSOR 2 MS.OL刀臂未在原点位置161015 LUBE ALARM CANNOT CYCLE START润滑油油量太低不能程序启动填加润滑油171016 AIR ALARM CANNOT CYCLE START气压压力太低不能程序启动检查空气压力(必须6~8kg/cm2)181017 TOOL NO. C0刀具号码大于刀库最大号码191018 MAG. NOT ORIENT刀库未定位检查刀库开关刀库重整(程序暂停+RESET)201019 NO. OF PARTS REACHED211020 ARM SENOR K7Q7 FAULT刀臂过载跳脱检查过载保护器Q7是否跳脱221021 ATC COUNTER ERROR刀库计数与检测信号不对检查刀库计数/检测开关刀库重整(程序暂停+RESET)231022 SPINDLE ALARM主轴警报241023 EMERGENCY STOP紧急停止252024 LOW LEVEL WATER切削液低水位a.检查水箱之水位是否过低b.检查水位开关是否故障262025 TOOL BROKEN DETECT刀具破损检知271026 BFD71可程序喷嘴角度超过设定值281027 5AXIS CLAMP第五轴在夹的状态291028 H/L GEAR POSITION ERROR高低档位置错误检查高低档开关是否正常301029 GEAR CHANGE OVER 10SEC变速箱高低档切换间操过10秒311030 GEAR OIL PRESSURE LOW变速箱油量低a.检查变速箱的油量b.检查压力开关是否故障321031 MAG RUN OVER TIME刀库运转超过时间331032 ARM IN TEST MODE刀臂在测试模式将K0.3设为0341033 ATLM FAULT自动刀长量测警报352034 FRONT DOOR OPENCE规格前门未关闭关闭前门362035 SIDE DOOR OPENCE规格侧门未关闭关闭侧门371036 DEVICE NOT CLAMP治具没有夹381037 AXIS NOT HOME OK轴没有归原点将轴归原点392038 MIST LOW FLOAT低水位401039 HYDRAULIC FAULT油压单元故障412040 FILTER DIRTYC.T.S滤网脏清除滤网或更换滤网422041 C.T.S. LOW PRESSUREC.T.S 压力低检查管路是否阻塞431042 ARM NOT IN U/C POS刀臂没有在原点位置441043 ARM NOT IN C POS刀臂没有在扣刀位置451044 LUBE LOW PRESSURE润滑油压力低461045 DOOR NOT CLOSE CANNOT CYCLE START安全门未关闭不能程序启动472046 PLS PRESS DOOR CLOSE AGAIN482048 PLS DOOR CLOSE USE HANDMITSUBISHI 刀臂式机器警报讯息 2007/2/12Page:2/