10t单钩移动电动葫芦的传动系统设计-毕业设计论文.docVIP

PAGE 66 摘要 电动葫芦是一种轻小型起重设备。它主要由减速器，运行机构，卷筒装置，吊钩装置，联轴器，限位器，锥形转子电动机等部分组成。本文根据设计任务书要求，主要对10t单钩移动电动葫芦的总体方案选择和确定，然后对传动系统进行设计。根据设计要求和目的，参考CD型电动葫芦,首先对10t单钩移动电动葫芦进行结构分析，选择合理机构及装配方案，然后对减速器进行设计，钢丝绳的选用及强度验算，卷筒的参数计算及验算，再计算齿轮的传动比，确定各个齿轮的参数，进行强度计算,选择合理的轴承、键、轴套等各种零部件，画出总体装配图。 关键词：电动葫芦，吊钩，减速器  Abstract Electric hoist is a kind of small lifting equipment. It is mainly formed by reducer, running organizations, drum installation, hook device, the coupling stopper, conical rotor motor and other components. According to the design task demands, this book mainly against to 10 t mobile electric hoist single hook selection and determination of the overall program, and then design the transmission system. According to the requirements and objectives of the design, reference CD-type electric hoist on the first take the 10 t mobile electric hoist with the single hook for the structure analysis, select reasonable organization and assembly programs, then design the reducer, selection of wire rope and strength checking, reel the parameter calculation and checking, and calculate the gear transmission ratio, to determine the parameters of each gear, the strength calculation, select a reasonable bearing, keys, bushing and other components, to draw general assembly drawing. Keywords: electric hoist, hook, reducer  目录 TOC \o 1-3 \h \z \u HYPERLINK \l _Toc 摘要 PAGEREF _Toc \h I HYPERLINK \l _Toc Abstract PAGEREF _Toc \h II HYPERLINK \l _Toc 1 绪论 PAGEREF _Toc \h 1 HYPERLINK \l _Toc 1.1 概述 PAGEREF _Toc \h 1 HYPERLINK \l _Toc 1.2 起重机势发展趋势 PAGEREF _Toc \h 1 HYPERLINK \l _Toc 1.2.1 技术发展趋势 PAGEREF _Toc \h 1 HYPERLINK \l _Toc 1.2.2 产品发展趋势 PAGEREF _Toc \h 3 HYPERLINK \l _Toc 1.3 国内钢丝绳电动葫芦的技术现状和发展方向 PAGEREF _Toc \h 4 HYPERLINK \l _Toc 1.3.1 CD1型钢丝绳电动葫芦存在的问题 PAGEREF _Toc \h 4 HYPERLINK \l _Toc 1.3.2 国内钢丝绳电动葫芦发展方向 PAGEREF _Toc \h 5 HYPERLINK \l _Toc 2 机构工作级别 PAGEREF _Toc \h 7 HYPERLINK \l _Toc 2.1 机构利用等级 PAGEREF _Toc \h 7 HYPERLINK \l _Toc 2.2 机构载荷状态 PAGEREF _Toc \h 7 HYPERLINK \l