基于PLC开发等离子熔射控制系统（毕业学术论文设计）.doc

┊ ┊ ┊ ┊ ┊ ┊ ┊ ┊ ┊ ┊ ┊ ┊ ┊ 装 ┊ ┊ ┊ ┊ ┊ 订 ┊ ┊ ┊ ┊ ┊ 线 ┊ ┊ ┊ ┊ ┊ ┊ ┊ ┊ ┊ ┊ ┊ ┊ ┊ 安徽工业大学 毕业设计（论文）说明书 共 页 第 PAGE 48 页 摘要 表面改性技术是研究的热点领域。然而，传统的表面改性技术，例如喷涂、电镀、化学热处理等，由于涂层与基体的粘接不牢固又或者是涂层太薄而不是很符合要求的。激光熔覆和等离子熔覆克服了传统表面改性的这些缺点，因而成为了近几年快速发展的主题。目前，等离子熔覆技术由于其良好的性能和低费用优势成为最为活跃的研究方向。 本文基于PLC开发等离子熔射控制系统,采用开放式协议实现与计算机二者之间通讯，并在计算机中编绘PLC的自动走刀位置控制程序。本文运用三菱公司推出的GX Developer 软件进行编程和仿真调试，从而达到本次研究的目的，等离子熔覆截齿软件编程与实现。 关键词：等离子； 熔覆； 截齿； PLC； 软件编程 Abstract Surface modification technique has become a hot field of research . But the traditional surface modification techniques，such as spraying，electroplating，chemical heat treatment，are not very satisfactory because the bonding of coating and substrate is poor or the thickness of the coating is too thin .The laser cladding and the plasma cladding overcome the shortcomings of the traditional surface modification and have been subjected to rapid development in recent years.Currently plasma cladding technique becomes the most active research direction because of its good performance and low cost advantages. This article based on PLC development plasma spray control system，using open protocol to communicate with the computer between the two, and automatic location of the tool path control program in the PLC and the computer compilation. TOC \o 1-3 \h \z \u HYPERLINK \l _Toc325977957 摘要 PAGEREF _Toc325977957 \h 1 HYPERLINK \l _Toc325977958 1. 绪 论 PAGEREF _Toc325977958 \h 3 HYPERLINK \l _Toc325977959 1.1 课题来源及意义 PAGEREF _Toc325977959 \h 3 HYPERLINK \l _Toc325977960 1.2 等离子及其等离子技术发展 PAGEREF _Toc325977960 \h 4 HYPERLINK \l _Toc325977961 1.2.1 等离子体基本知识 PAGEREF _Toc325977961 \h 4 HYPERLINK \l _Toc325977962 1.2.2 等离子熔覆的概述 PAGEREF _Toc325977962 \h 5 HYPERLINK \l _Toc325977963 1.3 等离子熔覆截齿的国内外现状 PAGEREF _Toc325977963 \h 6 HYPERLINK \l _Toc325977964 1.3.1 截齿的生产工艺现状及其使用情况 PAGEREF _Toc325977964 \h 6 HYPERLINK \l _Toc325977965 1.3.2 等离子熔覆截齿的引入 PAGEREF _Toc325977965 \h 8 HYPERLINK \l _Toc325977966 1