网站大量收购闲置独家精品文档,联系QQ:2885784924

低功耗四通路数模转换芯片的设计-微电子学与固体电子学专业论文.docx

低功耗四通路数模转换芯片的设计-微电子学与固体电子学专业论文.docx

  1. 1、本文档共70页,可阅读全部内容。
  2. 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
  3. 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载
  4. 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
低功耗四通路数模转换芯片的设计-微电子学与固体电子学专业论文

II II ABSTRACT The digital to analog converters (D/A converter) is used widely as the conjunctive circuit of digital electronic system and analog electronic system. So it’s worth to design an D/A converter with the features of high speed, lower power consuming and high accuracy. A voltage-segmented D/A converter is designed which has voltage features of monotony. The input mode is serial-input, which meets the requirement of medium-speed; and the output mode is voltage-output, which could satisfy the demand of mass application. The chip is 8-bit which operates from a single +2.7V to +3.6V supply. There are quad-channels in chip. We can select channels to output by control-signal. Chip can be turn to shutdown mode by extern signal to decrease the power consuming. The supply current is 0.7mA while operating and 1μA in shutdown mode. The operational amplifier is designed, whose input and output swing rail to rail, which could satisfy the demand of D/A converter. For the design of the bandgap reference, the architecture of exponential curvature-compensated and the feedback circuit are employed, which satisfy the requirement of the low temperature coefficient (TC) and high power-supply rejection ratio (PSRR). The TC is 12ppm/℃, and the PSRR is 159μV/V. We run simulation with 0.6μ m BiCOMS process, and results of system simulation indicate that the INL and DNL of the DAC chip are both less than 1LSB, the settling time is less than 6μs. Design of each block is described. Performances of output operational amplifier and the bandgap reference circuit have a very deep influence on the D/A converter, so the research of the two parts’ design is focused on. Layout consideration is also presented in brief and the simulation waves are given. Keywords: D/A converter Voltage-mode Operational amplifier Bandgap reference PAGE PAGE IV 目 录 摘 要 ···············································································································I HYPERLINK \l _bo

您可能关注的文档

文档评论(0)

peili2018 + 关注
实名认证
内容提供者

该用户很懒,什么也没介绍

1亿VIP精品文档

相关文档