柴油机空气滤清器首次拉深工艺分析及模设计说明书.docVIP

柴油机空气滤清器首次拉深工艺分析及模具设计 摘要 本次柴油机空气滤清器首次拉深工艺分析及模具设计为用模具生产无凸缘筒件，柴油机空气滤清器的制造过程经过工艺分析后，可知包括落料、拉深、二次拉深、三次拉深、切边等工序。经过方案分析后把落料和首次拉深用复合模完成，而其他不出图但进行了相关的尺寸计算，重点在复合模上，解决落料和拉深的计算问题同时对相关的模具的零件给以详细的设计。生成装配工程图和相关的零件刚才图。 关键词：模具，落料，拉深，装配图 The first drawing process analysis and die design of diesel engine air filter ABSTRACT The diesel engine air filter first drawing process analysis and die design for the production of flangeless cylinder mould, diesel engine air filter manufacturing process by process analysis, it includes blanking, drawing three times, two times drawing, deep drawing, trimming process. After analysis the blanking and drawing the first time, complete with compound die, while the other is not drawing but to calculate the correlation dimension, focusing on the compound die, at the same time give parts of the die of the detailed design to solve the problem of the calculation of blanking and drawing. Generation of assembly drawings and related parts just map. KEYWARDS：die ，deep drawing ，assembly drawing ，parts drawing 目录 TOC \o 1-3 \h \u HYPERLINK \l _Toc30737 摘要 PAGEREF _Toc30737 I HYPERLINK \l _Toc1142 ABSTRACT PAGEREF _Toc1142 II HYPERLINK \l _Toc30142 1绪论 PAGEREF _Toc30142 1 HYPERLINK \l _Toc24688 1.1 引言 PAGEREF _Toc24688 1 HYPERLINK \l _Toc7919 1.2 冲压的定义 PAGEREF _Toc7919 1 HYPERLINK \l _Toc31008 1.3冲压工序分类 PAGEREF _Toc31008 2 HYPERLINK \l _Toc13616 1.4冲压工艺的特点应用 PAGEREF _Toc13616 2 HYPERLINK \l _Toc15881 2.工艺分析 PAGEREF _Toc15881 3 HYPERLINK \l _Toc21907 2.1材料分析 PAGEREF _Toc21907 3 HYPERLINK \l _Toc32034 2.2 结构形状分析 PAGEREF _Toc32034 3 HYPERLINK \l _Toc28318 2.3圆角半径分析 PAGEREF _Toc28318 3 HYPERLINK \l _Toc2463 2.4拉深件的尺寸精度分析 PAGEREF _Toc2463 3 HYPERLINK \l _Toc12912 3.拉深工序设计 PAGEREF _Toc12912 4 HYPERLINK \l _Toc12788 3.1设计工艺方案 PAGEREF _Toc12788 4 HYPERLINK \l _Toc20275 3.2工艺方案特点的比较 PAGEREF _Toc20275 4 HYPERLINK \l _Toc18177 3.3确定工艺方案 PAGEREF _Toc18177 5 HYPERLINK \l _Toc18468 4.拉深件工艺参数的计算 PAGEREF _Toc18468 6 HYPERLINK \l _Toc17799 4