同异频切换地参数配置.docxVIP

同异频切换的参数配置 A1事件： 事件进入条件：Ms - Hys Thresh 停止异频测量门限：Threshold th2a for RSRP(Threshold2a) A1迟滞：Related hysteresis of threshold th2a for RSRP (hys threshold2a) 服务小区的RSRP- hys threshold2a Threshold2a，且保持时间超过a1TimeToTriggerDeactInterMeas 的设置时间，则停止异频测量。 A2事件： 启动同频测量门限threshold1 事件进入条件：Ms + Hys Thresh 启动异频测量门限：Threshold th2 interFreq for RSRP (threshold2InterFreq ) A2迟滞：Related hysteresis of threshold th2 interfreq for RSRP(hysThreshold2InterFreq ) 打开Enable interfrequency handover:异频切换开关 Time to trigger for A2 to activate inter measurement( a2TimeToTriggerActInterFreqMeas ) 当服务小区的RSRP+ hysThreshold2InterFreq threshold2InterFreq，且保持时间超过的设置时间 a2TimeToTriggerActInterFreqMeas ，则开始异频测量 A3事件 事件进入条件：Mn + Ofn + Ocn - Hys Ms + Ofs + Ocs + Off 事件离开条件：Mn + Ofn + Ocn + Hys Ms + Ofs + Ocs + Off NSN无Ofn/Ocn/Ofs/Ocs 参数 同频A3事件 同频A3迟滞：Related hysteresis of offset a3offset for RSRP intra F(hysA3Offset ) A3报告时长:A3 report interval A3触发时延:A3 time to trigger A3偏置:A3offset 故同频A3事件需满足：邻小区的RSRP-hysA3Offset 服务小区的RSRP+ a3Offset ，由于hysA3Offset配置为0，故A3事件的示意图如下图所示： 异频A3事件 异频A3偏置 A3 offset RSRP inter frequency a3OffsetRsrpInterFreq 异频A3报告时长：A3 report interval RSRP inter frequency 异频A3触发时延：A3 time to trigger RSRP inter frequency 异频A3迟滞：Related hysteresis offset a3offset RSRP inter frequency hysA3OffsetRsrpInterFreq 异频A3事件满足：邻小区的RSRP—hysA3OffsetRsrpInterFreq 服务小区的RSRP+ a3OffsetRsrpInterFreq A5事件： 事件进入条件：Ms + Hys Thresh1 且 Mn + Ofn + Ocn- Hys Threah2 诺西无Ofn/Ocn参数 同频A5事件： Thresh1:Threshold th3 for RSRP(threshold3 ) Thresh2 :Threshold th3a for RSRP threshold3a A5报告时长A5 report interval A5触发时延A5 time to trigger A5迟滞Related hysteresis th3 and th3a for RSRP 同频A5事件满足：当服务小区的 RSRP+hysThreshold3threshold3,且邻区RSRP- hysThreshold3threshold3a 由于现网中的迟滞配置为0，故只要服务小区低于threshold3，邻区高于threshold3a，并达到触发的时间，就会发生切换，其示意图如图所示： 异频A5事件： Thresh1:Threshold th3 for RSRP inter frequency （threshold3InterFreq ） Thresh2 :Threshold th3a for RSRP inter frequency （threshold3aInterFreq ） A5报告时长A5 report interval inter