光印电路板制作过程.docVIP

光印电路板制作过程 　　光印路板制作程电电电电电电电 　　本文国外朋友写的光印路板的制作程,板子为为为为为为为为为为为为为为为为为为为为为为10年前就有了,想想当年拜托 　　为为为为为为为为为为为为为为为为为为为为为为为为人将路板文件打印到胶片人都不答,收也, 　　主要是当激光打印机太了,那候光印路板价格也,为为为为为为为为为为为为为为为为为为为为为为 　　为为为为为为为为为为为为为为为为为在不知道价格是多少了,因好久都没有用了,在主要采用 　　为为为为为为为为为为为为为为为印,当然,光印也有自己的点,就是制作方便,而且做出 　　来的效果也相当不,就是成本偏,有些偏地方有可能为为为为为为为为为为为为为为为为为为为 　　不到光印路板。况且如果只制作一次,那胶片就只为为为为为为为为为为为为为为为为为为为为 　　用一次,我是得有点浪胶片。为为为为为为为为为为为为为 　　制作程相当,将路板打印到胶片上,可以先不为为为为为为为为为为为为为为为为为为为为为为为 　　管正反面,，格意上做的要究正反面,因如果正反为为为为为为为为为为为为为为为为为为为为为 　　面不的,在做很条的候效果不好。,,在暴光为为为为为为为为为为为为为为为为为为为为为为为 　　为为为为为为为为为为为为为为为为为为为为为为为为为为为为为为为为为候将正反面了,因如果正反面弄了就相当麻了。暴光大概是8分为 　　左右就可以了,一般的光印路板上都有明要求。影的候注为为为为为为为为为为为为为为为为为 　　意溶液度,千万度影了。为为为为为为为为为为为为 　　本文介的腐方法是三化,我得个容易因比黑,为为为为为为为为为为为为为为为为为为为为为为为为 　　不容易看清楚,最好是使用双氧水与酸配置,但是要注为为为为为为为为为为为为为为为为为 　　意酸有性,要注意通。为为为为为为为为为为为为为为 　　In answer to the frequently asked question about how I make my Printed Circuit Boards (PCB’s) 　　I make almost professionally looking PCB’s since years, the only thing I can’t do by myself is the silkscreen mask. 　　The basic PCB material I use is presensibilized with a UV sensible lacquer (available in most electronic stores). 　　You can also use non presensibilized PCB material and treat it with Positiv20 spray from Kontakt Chemie. De-oxidate and de-grease the raw PCB material with steel wool and aceton. Atomise a FINE layer of Positiv20 onto the copper and let the PCB dry for 24 hours in ambient room temperature, or about an hour at a maximum of 70?C (do not exceed! ). I do this in my hot air electric oven in the kitchen. 　　The drying MUST be done in complete darkness! After that the PCB can be used as normal presensibilized PCB. 　　All you need is: 　　?A software to develop your PCB layouts. I use the demo version of Circad’98 from 　　Holophase because of its ease of use. 　　I also recently bought the cheap Sprint-Layout software from Abacom. 　　?(Preferably) A laserprinter to print the darkest possible printouts of your PCB layout 　　on transparent slides. 　　I always print out two identical and mirror