第一章 航空数字化制造技术.ppt

---THE END--- 做好個人道德素養；不要因為貪小便宜，貪一時方便而不顧道德品行丟失把人格尊嚴都降低了。 因為一個人把道德品質丟失了，再想建立起來將是萬分的困難。 所以每個人都應該尊首道德底線，不應敗壞基本道德品質。 以下是公司裡面出現的不好的現象： 1、厕所紙巾偷到宿舍去用 2、車間應急藥箱裡面的藥偷走 （偷盜行為可恥） 以下是公司裡面出現的不好的現象： 1、公共场所随意扔垃圾 2、電視房垃圾亂丟 以下是公司裡面出現的不好的現象： 恶意损坏公共财物 以下是公司裡面出現的不好的現象： 吃饭不要浪废食物 道德與生活 從字義看兩者的意義與差別: 1、倫理的意義: 倫—類別、關係；理—紋理、道理。 倫理—人類社會裡種種身分間合理的關係，行為分際(做人要守本分)。(哪些人際關係、身分) 2、道德的意義: 道—道路、道理；德—獲得。 道德—走人走的道路，便可獲得人的待遇。(不走捷徑、不誤入歧途→尊嚴、榮譽)人道 (ps.如何批評一個人罔顧為人?) 道德與生活 1、利己: 理性認識到遵守規範有利於己。(奸商 / 信譽商人) 2、利人: 追求人性中的真、善、美。(崇高的可能性)。 (愛人者人恆愛之，敬人者人恆敬之；德不孤必有鄰。)(典範在夙昔--林靖娟、鐵達尼號的樂師、德雷莎修女、史懷德….) 3、利己利人: 兼顧自我理想與社會進步。Bill Gates? 不做”損人利己”之事。 Ps.回想郭爾堡的道德認知理論、馬斯洛的需求層次理論。 * Current Warner Robins tool fabrication process. Time varies with starting data: loft data in a book, Mylars, electronic loft data, or model part (reverse engineering). After an electronic version of the part shape is prepared, a male plaster tool is built using contour boards that are cut on a water jet router. This tool is fabricated to the shape of the part, not a springback corrected shape. Then a female plaster tool is made, and finally a fiberglass forming tool (male) is produced. In tool tryout, a part is formed, trimmed and measured, then the tool is often reworked to get the correct shape. Subsequently, trim lines are scribed on the tool and a trimming template is fabricated. The tool and trimming template are then stored until needed again. The entire process takes approximately 365 labor hours over a period of 53 work days. * The to-be process at Warner Robins consists of: 1) Entering the data and generating an electronic version of the tool shape and forming process. 2) Prediction of the corrected tool shape. 3) Forming the part on the reconfigurable tool. 3) Water jet trimming the part using a support fixture that was designed in step 1 and cut on the water jet. 4) Measurement of the part using a rapid optical technique. 5) Comparison of the part shape to the desired sh