DHT11程序代码.docVIP

//现象是循环显示温度和湿度各显示三秒(小数位显示0) //若需将dht11.c和其他的硬件结合使用,只需在需用到温湿度值的文件加下面声明 //extern int wendu, shidu;(wendu是温度值,shidu是湿度值,比实际的温湿度值扩大了十倍) //一、 //文件名保存为main.c /********************************************************************************************/ //除了dht11的接口外,其他的电路原理图与天祥的C51板对应 //现象是循环显示温度和湿度各显示三秒 #include dht11.h #include reg52.h sbit DULA = P2^6; //数码管位定义 sbit WELA = P2^7; static unsigned char flag; //中断计数标志 static unsigned char code array[]= { //数码管编码 0x3f,0x06,0x5b,0x4f,0x6, 0x6d,0x7d,0x07,0x7f,0x6f }; extern int wendu, shidu; static void InitTime(void); void Delay_1ms(unsigned int ms); static void SMG_Display(unsigned int value); int main(void) { unsigned char mark = 0; //先等上电稳定 Delay_1ms(1000); //因为读一次数据dht11才会触发一次采集数据. //即在先使用数据时采集一次数据 ReadTempAndHumi(); //因为在两次采集数据需一定的时间间隔,这里还可减少 Delay_1ms(3000); //设定定时器 InitTime(); while(1) { //三秒读一次温湿度 if(flag == 60) { flag = 0; mark++; /* //读温湿度,可检测函数调用是否失败, //函数返回OK(1)表示成功,返回EROR(0)表示失败 //OK和EROR是在dht11.H中定义的宏 */ ReadTempAndHumi(); } if(mark % 2 == 0) { //显示温度 SMG_Display(wendu); } else { //显示湿度 SMG_Display(shidu); } } return 0; } //设定定时器 static void InitTime(void) { TH0 = (unsigned char)((65535 - 50000) 8); TL0 = (unsigned char)(65535 - 50000) ; TMOD = 0X01; TR0 = 1; ET0 = 1; EA = 1; } //数码管显示函数 static void SMG_Display(unsigned int value) { unsigned char ge, bai, shi; ge = value % 10; shi = value % 100 / 10; bai = value % 1000 / 100; WELA = 1; P0 = 0XFE; WELA = 0; P0 = 0XFF; DULA = 1; P0 = array[bai]; DULA = 0; Delay_1ms(2); WELA = 1; P0 = 0XFD; WELA = 0; P0 = 0XFF; DULA = 1; P0 = array[shi]; P0 |= 0x80; /*显示小数点*/ DULA = 0; Delay_1ms(2); WELA = 1; P0 = 0XFB; WELA = 0; P0 = 0XFF; DULA = 1; P0 = array[ge]; DULA = 0; Delay_1ms(2); } //中断函数 void timer(void) interrupt 1 { TH0 = (unsigned char)((65535 - 50000) 8); TL0 = (unsigned char)(65535 - 50000); fla