LTE NM11_C1_0 信令流程解析-176.pptVIP

Inter-eNB S1 HandOver – 异常过程5 Sampling Point 7’: The source eNB receives the RRCConnectionReestablishmentRequest message from the UE. Inter-eNB S1 HandOver – 异常过程6 异常过程：网管信令图示 Inter-eNB S1 HandOver – 异常过程7 Sampling Point 7’: The target eNB receives the RRCConnectionReestablishmentRequest message from the UE. Inter-eNB S1 HandOver – 异常过程8 异常过程：网管信令图示 目标侧: 源侧: Inter-eNB S1 HandOver – 异常过程9 Sampling Point 7’: The target eNB receives neither the RRCConnectionReconfigurationComplete message nor RRCConnectionReestablishmentRequest from the UE,and the timer is timeout. Intra-eNB HandOver - Abnormal procedure2 Sampling Point 4’: The target cell of the eNB receives the RCConnectionReestablishmentRequest message from the UE, ,indicating handover Failure. Intra-eNB HandOver - Abnormal procedure3 异常过程：网管信令图示 Intra-eNB HandOver - Abnormal procedure4 Sampling Point 4’: The target cell of the eNB can receive neither the HANDOVER COMMAND nor HANDOVER PREPARATION FAILURE message from the MME and the timer is timeout, indicating handover failure. Intra-eNB HandOver - Abnormal procedure6 异常过程：网管信令图示 Inter-eNB X2 HandOver – 正常过程1 Sampling Point 1:当eNB收到测量报告，或是因为内部负荷分担等原因，触发了切换判决，进行eNB间小区间通过X2口的切换。 Sampling Point 2:源eNB通过X2接口给目标eNB发送HANDOVER REQUEST消息，包含本eNodeB分配的Old eNB UE X2AP ID，MME分配的MME UE S1AP ID，需要建立的EPS承载列表以及每个EPS承载对应的核心网侧的数据传送的地址。目标ENB收到HANDOVER REQUEST后开始对要切换入的ERABs进行接纳处理。 Sampling Point 3:目标eNB向源eNB发送HANDOVER REQUEST ACKNOWLEDGE 消息，包含New eNB UE X2AP ID、Old eNB UE X2AP ID、新建EPS承载对应在D侧上下行数据传送的地址、目标侧分配的专用接入签名等参数。 Inter-eNB X2 HandOver – 正常过程2 Inter-eNB X2 HandOver – 正常过程3 Sampling Point 4: 源eNB向UE发送RRC CONNECTION RECONFIGURATION，将分配的专用接入签名配置给UE。 Sampling Point 5: 源eNB将上下行PDCP的序号通过SN STATUS TRANSFER消息发送给目标eNB。同时，切换期间的业务数据转发开始进行。 Sampling Point 6: UE在目标eNB接入，发送RRC CONNECTION RECONFIGURATION COMPLETE消息。表示UE已经切换到了目标侧。 Sampling Point 7:目标eNB给MME发送PATH SWITCH REQUEST消息，通知MME切换业务数据的接续路径，从源eNB到目标eNB，消息中包含原侧侧的MME UE S1AP ID、目标侧侧分配的eNB UE S1AP 、EPS承载在目标侧将使用的下行地址。 Sampling Point 8: MME返回P