工程术语英汉对照.docVIP

HYPERLINK /bbs/simple/index.php? 超级英语俱乐部 - HYPERLINK /bbs/simple/index.php?f18.html 工程设计 | Engineering Designing - HYPERLINK /bbs/simple/index.php?t10172.html 工程术语英汉对照 /bbs/simple/index.php?t10172.html AAdapt/modify (v)修改; adapt the mould 修模; Adaptation/modification (n);Anodize (v)作阳极处理;anode coating 阳极镀层; anodic 阳极处理; anodized finish 阳极化拋光;BBoss 凸台,螺丝柱;Bubble 气泡; [射出成型不良]logo bubble 铭牌,铭板;一般用透明PVC印制或为直接注射件;Buckle 扣具;? ?male buckle 公扣;? ?female buckle 母扣;Burr 毛边; [射出成型不良]CCap 盖子;screw cap 螺帽;螺母;end cap 太阳片[一种轴用介子,中间孔因有倒刺,可防松脱];Cavity 槽,穴;? ?Wheel cavity 轮槽;Clearance 间隙;side to side wheel clearance 轮子两边间隙;Coat (v)表面涂装[如烤漆,电镀,喷油等]; coating (n)涂层;elctrodeposited coating电镀层;? ?metal coating 金属涂装/镀层;? ?spray coating 喷涂层;? ?dash coating 泼涂层;Crack 裂痕[射出成型不良];Crown 突起;top crown 顶凸[射出成型不良];Cut out / slot 缺口;DDiameter 直径;centering diameter 中心距;hole diameter 孔径;ID = inside diameter 内径;OD = outside diameter 外径;FFillet 倒角,圆角;Finish 拋光;表面最后状况;精加工;表面涂层;? ?gloss finish 拋光;? ?stoving finish 烤漆;? ?surface finish 表面光洁度;Fit (v)配合;clearance fit 间隙配合;fit tolerance 配合公差;fitting problem = tolerance problem 合配问题/公差问题; ? press fit 压入配合;紧配合;Fixture 夹/治具;GGate 浇口; ? direct gate 直浇口side gate 侧状浇口; ring gate 环形浇口; overlap gate 重叠浇口; tab gate 片状浇口; fan gate 扇形浇口; film gate 腊状浇口; disk gate 盘形浇口; point gate 点状浇口; submarine gate/tunnel gate 潜状浇口;HHole 孔;oval hole 椭圆孔; blind hole 不通孔;盲孔;hole diameter 孔径;Hook (v)挂住;(n)挂钩;Housing 外盖,轮架IInject (v)射出; ? ? Injection (n)射出;injection point 进浇点;injection pressure 射出压力;injection speed 射出速度;injection temperature 射出温度;Insert 埋入件;镶件;塞子;insert support;Intercourse 相交,相接;Increase the length of the intercourse between each tube. 增大每根管子间的重叠度Interfere 干涉;interference problem 干涉问题;LLine 线条;纹路? ?flow line 流纹;? ?parting line 分型线;? ?weld line 熔合线;MMark 痕迹; burn mark 烧焦; [射出成型时,因排气不良所致]; flow mark 流痕;[射出成型不良];jetting mark 喷流痕[射出成型不良];Mold/mould 模具; mold base 模座; mou