塑料勺子注塑模具设计说明书资料.docVIP

注塑模具课程设计 摘要 本文以塑料勺为对象，详细介绍其注射模设计过程。设计中主要运用UG和AUTOCAD软件，根据制件的零件图进行零件的三维造型，并对该模型进行工艺分析，该塑件为壳体，浇注系统设计过程中，采取一模一腔侧浇口设计，并对成型零件进行了必要的计算和结构设计。采用龙记大水口标准模架，提高了设计效率。最后通过Autocad完成工程图的制作，设计中综合考虑了各方面的因素。 关键词：塑料勺，注射模，UG，侧浇口 Injection mould Design ABSTRACT The design of a set of blanking,punching mold. through access to information, the first parts to the process analysis, through process analysis and comparison, the use of blanking, punching process, through the blanking force, the top piece, and in terms of discharge power to determine the model press. Further analysis of the stamping dies for processing the application to select the desired type of mold design. The mold will be designed to draw upon the type of mold parts of the work expressed in the design process. Key words：Plastic spoon, Injection mould, UG, Side gate 目录 摘要 Ⅰ ABSTRACT Ⅱ TOC \o 1-3 \h \z \u HYPERLINK \l _Toc435953474 1 塑料成型工艺性分析 PAGEREF _Toc435953474 \h 1 HYPERLINK \l _Toc435953475 1.1 塑件分析 PAGEREF _Toc435953475 \h 1 HYPERLINK \l _Toc435953476 1.2 注射成型过程及工艺参数 PAGEREF _Toc435953476 \h 2 HYPERLINK \l _Toc435953477 1.3 PC的性能分析 PAGEREF _Toc435953477 \h 2 HYPERLINK \l _Toc435953478 2 拟定模具结构形式 PAGEREF _Toc435953478 \h 4 HYPERLINK \l _Toc435953479 2.1 分型面位置的确定 PAGEREF _Toc435953479 \h 4 HYPERLINK \l _Toc435953480 2.2 确定型腔数量和排列方式 PAGEREF _Toc435953480 \h 4 HYPERLINK \l _Toc435953481 2.3 模具结构形式的确定 PAGEREF _Toc435953481 \h 5 HYPERLINK \l _Toc435953482 3 注射机型号的确定 PAGEREF _Toc435953482 \h 6 HYPERLINK \l _Toc435953483 3.1 所需注射量的计算 PAGEREF _Toc435953483 \h 6 HYPERLINK \l _Toc435953484 3.2 注射机型号的选定 PAGEREF _Toc435953484 \h 6 HYPERLINK \l _Toc435953485 3.3 型腔数量及注射机有关工艺参数校核 PAGEREF _Toc435953485 \h 7 HYPERLINK \l _Toc435953486 4 浇注系统的形式和浇口的设计 PAGEREF _Toc435953486 \h 10 HYPERLINK \l _Toc435953487 4.1 主流道的设计 PAGEREF _Toc435953487 \h 10 HYPERLINK \l _Toc435953488 4.2 冷料穴的设计 PAGEREF _Toc435953488 \h 12 HYPERLINK \l _Toc435953490 4.3 浇口的设计 PAGEREF _Toc435953490 \h 12 HYPERLINK \l _