- 1、本文档共72页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
本科生毕业设计(论文)
PAGE V
毕业设计(论文)
EQ1181型载货汽车变速器取力器设计说明书
摘 要
本次设计的取力器是与EQ1181型载货汽车DF6S850型变速器匹配,变速器最大输出扭矩850Nm,要求:取力器最大输出扭矩450Nm;满足强度、刚度要求;较高的传递效率;良好的加工工艺性和装配工艺性。该取力器的取力形式为变速器左侧盖取力器,总体结构形式采用两轴式,从取力器到专用装置之间的动力传递可以采用机械传动。首先,根据EQ1181型货车发动机和变速器参数及所用专用装置的参数确定取力器传动比,根据装配空间确定取力器内两齿轮中心距范围,根据变速器取力齿轮参数确定取力器两齿轮的模数,压力角,齿宽等参数。其次,对轴、齿轮和键进行校核,验证各部件的可靠性。然后,完成取力器装配图和零件图的绘制。最后,编制部分零件的加工工艺过程。
通过计算分析,该取力器结构设计合理,制造工艺简单,基本可以用于实际生产和使用,达到设计要求。
关键词:货车;变速器;取力器;设计;工艺。
Abstract
This design requires access edge with transmission DF6S850 of EQ1181 Truck matching, Request: the maximum output torque transmission 850Nm,get maximum output torque of Power 450Nm; to meet the strength and stiffness requirements; high transmission efficiency; good processing process and assembly process of. The devices take power from the power form of power transmission from the left side of cover, and the overall structure of the form of a two-axis, taking power from the device to a dedicated power transfer between the devices can be used mechanical transmission. First of all, the EQ1181-type vehicle in accordance with engine and transmission parameters and a dedicated device used to determine the parameters of Power from the transmission ratio, determined in accordance with the assembly of space inside edge from the center distance of two gear range, under the power transmission gear parameters taken from the two gear power devices module, pressure angle, tooth width and other parameters. After the shaft, gear and keys to check to verify the reliability of the components. Then, check our complete device assembly drawing and components drawing. Finally, the preparation of parts of the processing process.
Analysis by calculating the force from a reasonable structure design, manufacturing process is simple, the basic can be used in actual production and use, meet the design requirements. Key words:truck;transmission; power take off; design;technology.
目 录
TOC \o 1-3 \f \h \z 第一章 绪 论 1
1.1取力器简介 1
1.2取力器分类 1
文档评论(0)