数控技术专业英语 教学课件 作者 刘瑛 04.pptVIP

4.3 Loop Systems for Controlling Tool Movement Configuration for an open loop system （开环系统的配置）Figure 4.7 4.3.1 Open Loop Systems 4.3.2 Closed Loop Systems Configuration of a closed loop system. （闭环系统的配置。）Figure 4.8 Vocabulary open loop system 开环系统 closed loop system 闭环系统 feedback [5fi:dbAk] n. 反馈 pulse [pQls] n. 脉冲，脉搏 ball-nut n. 球状螺母 lead screw 丝杠 servo [5sE:vEu]n. 伺服, 伺服系统 servomechanism [5sE:vEu5mekEnizEm] n.伺服机构(系统), 自动控制装置 current [5kQrEnt] adj. 电流 resolver [ri5zClvE] n.旋转变压器 circuitry [5sE:kitri] n. 电路, 线路 substantial [sEb5stAnFEl]adj. 坚固的, 实质的, 真实的, 充实的 saving [5seiviN] n. 节约，存款, 挽救, 救助 represent [7ri:pri5zent] v. 代表；声称；表现 Notes 1．One of the important factors determining the tolerance to which a part can be cut is the loop system type. 决定工件加工误差大小的一个重要因素就是控制系统的类型。 * * Introduction 4.1 Positioning Control 4.2 Unit 4 Machine movements and control Loop Systems for Controlling Tool Movement 4.3 4.1 Introduction 4.2 Positioning Control 4.2.1 Point-to-Point Component detail involving point-to-point positioning. （点位定位的零件图。）Figure 4.1 4.2.2 Line Motion Component detail involving line motion. （涉及直线运动的零件图。）Figure 4.2 Resulting tool path when three slides move simultaneously. （三个溜板同时运动时形成的刀具路径。）Figure 4.3 Vocabulary slide [slaid] n.溜板 predetermine [5pri:di5tE:min] v. 预定, 预先确定 describe [dis5kraib] vt. 描写, 记述, 形容 point-to-point n. 点到点，点位运动 motion [5mEuFEn] n. 运动, 动作 linear [5liniE] adj. 线的, 直线的, 线性的 interpolation [in7tE:pEu5leiFEn] n.插补 contouring [kEn5tuEriN] n. 轮廓 circular [5sE:kjulE] adj. 圆形的, 循环的 involve [in5vClv] vt. 包括, 笼罩, 潜心于, 使陷于 identify [ai5dentifai] v. 识别, 鉴别, 确定 instruction [in5strQkFEn] n. 指示, 用法说明, 指导, 指令 coordinate [kEu5C:dinit] vt. 调整, 整理 occur [E5kE:] vi. 发生, 出现 simultaneously [7simEl5teinjEsli] adv. 同时地 maximum [5mAksimEm] n. 最大量, 最大限度, 极大adj. 最高的, 最多的, 最大极限的 prior to [5praiE] adv. 在前, 居先 result from 由...产生 feed rate进给率 slot [slCt] n. 缝, 狭槽 in relation to 相对于，关于，涉及 workpiece [5wE:kpi:s] n. 工件 continuous [kEn5tinjuEs] adj. 连续的, 持续的