奔驰车身点焊标准_图文.docVIP

下载本文档

78
0
约3.01万字
约 35页
2020-07-01 发布于湖北
举报
版权申诉

奔驰车身点焊标准_图文.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

Mercedes-Benz MBN 10 382 Engineering Standard Date Published: 2005-05 Category: 37 Total No. of Pages (Including Annex: 20 Person in Charge: Michael Ruther Plant 050; Dept.: PWT/VFT Date of Translation: 2005-08 Phone: +49(07031-90-79302 Resistance Spot Welding of Steel, Thickness up to 3 mm Widerstandspunktschwei?en von Stahl bis 3 mm Foreword Due to more complex requirements resulting from the increased use of high-strength and ultra high- strength steels, resistance spot welding is subject to continuous adaptation. This Standard super- sedes the previous Mercedes-Benz spot welding standard F0 93050055317. Changes In comparison with F0 93050055317 edition 2000-05, the following changes have been made: ?Extension of material spectrum (high-strength and ultra high-strength steels ?Suitable welding parameters for high-strength and ultra high-strength steels ?Introduction of weld spot classes ?Design of welding gun, transformer, welding control system, peripherals ? Reworking concept NOTE: No guarantee can be given in respect of this translation. In all cases the latest German-language version of this Standard shall be taken as authoritative. Copyright DaimlerChrysler 2005 Contents 1Scope2 2Normative References3 3Abbreviations, Acronyms, Definitions, Symbols3 4Regulated Substances and Recyclability4 5General4 5.1Design of Welding Gun4 5.2Design of Control System and Transformer4 5.3Design of Process4 5.4Design of Peripherals4 6Weld Spot Classes5 6.1Definitions5 6.2Definition of Special Spots5 6.3Criteria for Special Spots5 6.4Special Measures Required for Special Spots5 7Welding Parameters for 2-Sheet Welds6 7.1Standard Value Table6 7.2Electrode Force6 7.3Welding Current7 7.4Welding Time7 7.5Squeeze Time7 7.6Hold Interval7 7.7Preheating7 7.8Standard Values for 2-Sheet Welds8 83-Sheet and 4-Sheet Welds10 8.1General 10 8.2Sheet Arrangements10 8.3Welding Parameters11 8.4Electrodes 12 8.5Nugget and Spot Diameters for 3-Sheet Welds12 9Minimum Flange Widths13 9.1Minimum Fla