- 1、本文档共41页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
PAGE
PAGE II
摘 要
本文主要研究电射流打印的基本原理,设计低成本亚微米3D打印机结构,设计打印平台运动部件、墨水进给系统、喷针加热模块等,编写打印平台运动控制程序,设计完整的3D打印机样机,实现复杂亚微米图形的3D打印。
本文通过市场调研、可行性方案论证、方案对比的方法设计了一款龙门式电射流3D打印机,该3D打印机采用同步带和丝杠传动结构,Z向双电机同时驱动,以保证运动精度。墨水进给系统采用微量注射器完成,利用USB显微镜实现对射流状态的实时监测。本次设计是校核和计算的基础上,装配并且设计了3D打印机中的所有零件,设计出符合要求的3D打印机。
关键词:电射流;3D打印机;结构设计;
Abstract
This paper mainly studies the basic principle of electric jet printing, designs low-cost sub-micron 3D printer structure, designs printing platform moving parts, ink feeding system, needle heating module, etc., writes printing platform motion control program, and designs a complete 3D printer prototype. Implement 3D printing of complex sub-micron graphics.
This paper designs a gantry electric jet 3D printer through market research, feasibility scheme demonstration and scheme comparison method. The 3D printer adopts synchronous belt and screw drive structure, and Z-direction dual motor drives at the same time to ensure the motion precision. The ink feed system is completed using a micro-syringe, which uses a USB microscope to achieve real-time monitoring of the jet state. By calculating and checking the design, the designed parts are assembled and designed to meet the requirements of the 3D printer.
Key words: electric jet; 3D printer; structural design;
PAGE V
PAGE V
目 录
TOC \o "1-3" \h \u 15731 摘 要 I
4840 Abstract II
30510 第1章 绪论 1
15391 1.1 3D打印技术的概述 1
30962 1.2 3D打印原理的分类 1
15543 1.2.1 选择性激光烧结技术 1
27418 1.2.2 熔融沉积造型 1
31116 1.2.3 立体光固造型技术 2
11607 1.2.4 数字光处理技术 2
12481 第2章 3D打印机结构方案设计及可行性论证 4
21905 2.1 3D打印机结构方案设计 4
30637 2.1.1 方案1 框架式3D打印机 4
18082 2.1.2 方案2 悬臂梁式3D打印机 4
17686 2.1.2 方案3 龙门式3D打印机 5
21061 2.2 3D打印机方案可行性论证 6
29144 2.2.1 方案1评价 6
12730 2.2.2 方案2评价 7
14261 2.2.3 方案3评价 7
12428 2.3 方案确定 7
21157 第3章 3D打印机设计与计算 9
32692 3.1 技术参数及其坐标系的确定 9
19676 3.1.1 技术参数 9
15428 3.1.2 3D打印机坐标系选择 9
28258 3.2 电机的选择 10
20084 3.2.1 X方向电机的选择 10
9389 3.2.2 Y方向电机的选择 11
29092 3.3 滚珠
文档评论(0)